- 您現在的位置：買賣IC網 > PDF目錄140355 > W29GL032CT7A (WINBOND ELECTRONICS CORP) 2M X 16 FLASH 3V PROM, 80 ns, PBGA48 PDF資料下載
參數資料
| 型號： | W29GL032CT7A |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 80 ns, PBGA48 |
| 封裝： | GREEN, VFBGA-48 |
| 文件頁數： | 9/65頁 |
| 文件大小： | 650K |
| 代理商： | W29GL032CT7A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
W29GL032C
Publication Release Date: January 19, 2011
11
Preliminary - Revision B
7.2.12 Program Suspend/Resume
Once a program operation is in progress, a Program Suspend is the only valid instruction that maybe
executed. Verifying if the device has entered the Program-Suspend Read mode after executing the
Program-Suspend instruction, can be done by checking the RY/#BY and DQ6. Programming should
halt within 15s maximum (5s typical).
Any sector(s) can be read except those being program suspended. Trying to read a sector being
program suspended is invalid. Before another program operation can be executed, a Resume
instruction must be performed and DQ6 toggling bit status has to be verified. Use the status register
bits shown in the following table to determine the current state of the device:
Status
DQ7 DQ6 DQ5 DQ3 DQ2 DQ1 RY/#BY
Program suspend read in program suspended sector
Invalid
1
Program suspend read in non-program suspended sector
Data Data Data Data Data Data
1
Table 7-7
Polling During Embedded Program Suspend
Instruction sets such as read silicon ID, sector protect verify, program, CFI query can also be executed
during Program/Erase-Suspend mode.
7.2.13 Program Resume
The program Resume instruction is valid only when the device is in Program-Suspended mode. Once
the program resumes, another Program Suspend instruction can be executed. Insure there is at least
a 5s interval between Program Resume and the next Suspend instruction.
7.2.14 Programming Operation
Write Buffer Programming Operation, programs 32-bytes or 16-words in a two step programming
operation. To begin execution of the Write Buffer Programming, start with the first two unlock cycles,
the third cycle writes the programming Sector Address destination followed by the Write Buffer Load
Instruction (25h). The fourth cycle repeats the Sector Address, while the write data is the number of
intended word locations to be written minus one. (Example, if the number of word locations to be
written is 9, then the value would be 8h.) The 5
th cycle is the first starting address/data set. This will be
the first pair to be programmed and consequentially, sets the “write-buffer-page” address. Repeat
Cycle 5 format for each additional address/data sets to be written to the buffer. Keep in mind all sets
must remain within the write buffer page address range. If not, operation will ABORT.
The “write-buffer-page” is selected by choosing address A[20:5].
The second step will be to program the contents of the write buffer page. This is done with one cycle,
containing the sector address that was used in step one and the “Write to Buffer Program Confirm”
instruction (29h).
Standard suspend/resume commands can be used during the operation of the write-buffer. Also, once
the write buffer programming operation is finished, it’ll return to the normal READ mode.
Write buffer programming can be conducted in any sequence. However the CFI functions, autoselect,
Secured Silicon sector are not functional when program operation is in progress. Multiple write buffer
programming operations on the same write buffer address range without intervention erase is
accessible. Any bit in a write buffer address range cannot be programmed from 0 back to 1.
相關PDF資料 |
PDF描述 |
|---|---|
| WME128K8-150CCA | 128K X 8 EEPROM 5V, 150 ns, CDIP32 |
| WMS512K8VL-100DECEA | 512K X 8 STANDARD SRAM, 100 ns, CDSO32 |
| WMS512K8VL-85DECE | 512K X 8 STANDARD SRAM, 85 ns, CDSO32 |
| WF2M32B-90HM5A | 8M X 8 FLASH 5V PROM MODULE, 90 ns, CPGA66 |
| W7NCF01GH11CS7DG | 64M X 16 FLASH 3.3V PROM CARD, 150 ns, UUC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W29GL032CT7B | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 32MBIT 70NS 64LFBGA |
| W29GL032CT7S | 功能描述:IC FLASH 32MBIT 70NS 48TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:2,500 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（單線） 電源電壓:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| W29GL064C | 制造商:WINBOND 制造商全稱:Winbond 功能描述:64M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE |
| W29GL064CB7A | 功能描述:IC FLASH 64MBIT 70NS 48TFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6 |
| W29GL064CB7B | 制造商:Winbond Electronics Corp 功能描述:IC FLASH 64MBIT 70NS 64LFBGA |
發布緊急采購，3分鐘左右您將得到回復。