參數資料
型號: VN5770AK-E
廠商: 意法半導體
英文描述: Quad smart power solid state relay for complete H bridge configurations
中文描述: 四完整的智能功率H橋配置固態繼電器
文件頁數: 1/31頁
文件大?。?/td> 429K
代理商: VN5770AK-E
February 2007
Rev 2
1/31
31
VN5770AK-E
Quad smart power solid state relay
for complete H bridge configurations
Features
General features
– Inrush current management by active
power limitation on the high side switches
– Very low stand-by current
– Very low electromagnetic susceptibility
– In compliance with the 2002/95/EC
European directive
Protection
– High side drivers undervoltage shutdown
– Overvoltage clamp
– Output current limitation
– High and low side overtemperature
shutdown
– Short circuit protection
– ESD protection
Diagnostic functions
– Proportional load current sense
– Thermal shutdown indication on both the
high and low side switches
Description
The VN5770AK-E is a device formed by three
monolithic chips housed in a standard SO-28
package: a double high side and two low side
switches. The double high side is made using
STMicroelectronics VIPower M0-5 Technology,
while the low side switches are fully protected
VIPower M0-3 OMNIFET II. This device is
suitable to drive a DC motor in a bridge
configuration as well as to be used as a quad
switch for any low voltage application.
The dual high side switches integrate built-in non-
latching thermal shutdown with thermal
hysteresis. An output current limiter protects the
device in overload condition. In the case of long
overload duration, the device limits the dissipated
power to a safe level up to thermal shut-down
intervention. An analog current sense pin delivers
a current proportional to the load current
(according to a known ratio) and indicates
overtemperature shutdown of the relevant high
side switch through a voltage flag.
The low side switches have built-in non-latching
thermal shutdown with thermal hysteresis, linear
current limitation and overvoltage clamping.
Fault feedback for overtemperature shutdown of
the low side switch is indicated by the relevant
input pin current consumption going up to the fault
sink current flag.
Applications
DC motor driving in full or half bridge
configuration
All types of resistive, inductive and capacitive
loads
Type
R
DS(on)
I
OUT
V
CC
VN5770AK-E
280m
(1)
1.
Total resistance of one side in bridge configuration
8.5A
(2)
2.
Typical current limitation value
36V
SO-28
Table 1.
Order codes
Package
Tube
Tape and Reel
SO-28
VN5770AK-E
VN5770AKTR-E
www.st.com
相關PDF資料
PDF描述
VN6035L INDUCTOR 33UH 105MA 1210 10%
VN610SP-E SINGLE CHANNEL HIGH SIDE DRIVER
VN610SP13TR SINGLE CHANNEL HIGH SIDE SOLID STATE RELAY
VN610 SINGLE CHANNEL HIGH SIDE SOLID STATE RELAY
VN610SP INDUCTOR 4.7UH 150MA 1210 10%
相關代理商/技術參數
參數描述
VN5770AKP-E 功能描述:電源開關 IC - 配電 Quad Smart Power 280mOhm 8.5A 36VCC RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
VN5770AKPTR-E 功能描述:電源開關 IC - 配電 Quad Smart Power 280mOhm 8.5A 36VCC RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
VN5770AKTR-E 功能描述:固態繼電器-PCB安裝 36V, 8.5A Quad smart RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT
VN5772AK-E 功能描述:電源開關 IC - 配電 Quad Smart Power Solid-State Relay RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻(最大值):85 mOhms 開啟時間(最大值):400 us 關閉時間(最大值):20 us 工作電源電壓:3.2 V to 6.5 V 電源電流(最大值): 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5
VN5772AKTR-E 功能描述:功率驅動器IC Quad Smart Power Solid-State Relay RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube