參數資料
型號: UPD75116FGF
廠商: NEC Corp.
英文描述: 4-BIT SINGLE-CHIP MICROCOMPUTER
中文描述: 4位單片機
文件頁數: 45/78頁
文件大?。?/td> 549K
代理商: UPD75116FGF
45
μ
PD75108F,75112F,75116F
12.1 WHEN Ta = –40 to +50
°
C, V
DD
= 2.7 to 5.0 V
OPERATING VOLTAGE (Ta = –40 to +50
°
C)
CPU
*1
Programmable threshold port
(comparator input)
Other hardware
*1
*2
5.0
V
4.5
5.0
V
2.7
5.0
V
PARAMETER
TEST CONDITIONS
MIN.
MAX.
UNIT
*
1.
Except system clock oscillation circuit, programmable threshold port.
2.
The operable supply voltage range depends on the cycle time. See "AC CHARACTERISTICS".
OSCILLATION CIRCUIT CHARACTERISTICS (Ta = –40 to +50
°
C, V
DD
= 2.7 to 5.0 V)
RECOMMENDED
CONSTANT
TEST
RESONATOR
PARAMETER
MIN.
TYP.
MAX.
UNIT
CONDITIONS
Ceramic
resonator
After V
DD
reaches
MIN. of oscillation
voltage range
Crystal
resonator
External
clock
2.0
5.0
*3
MHz
4
ms
2.0
4.19
5.0
*3
MHz
V
DD
= 4.5 to 5.0 V
10
ms
30
ms
2.0
5.0
*3
MHz
100
250
ns
Oscillator
frequency (f
XX
)
*1
Oscillation
stabilization time
*2
Oscillator
frequency (f
XX
)
*1
Oscillation
stabilization time
*2
X1 input
frequency (f
X
)
*1
X1 input
high-/low-level width
(t
XH
, t
XL
)
X1
X2
μ
PD74HCU04
V
DD
= Oscillation
voltage range
X1
X2
C1
C2
X1
X2
C1
C2
*
1.
Oscillator frequency and X1 input frequency indicate oscillation circuit characteristics only. See AC
CHARACTERISTICS for instruction execution time.
2.
The oscillation stabilization time is the time required for oscillation to stabilize after V
DD
reaches MIN. of
oscillation voltage range or the STOP mode is released.
3.
When the oscillator frequency is 4.19 MHz < f
XX
5.0 MHz, PCC = 0011 should not be selected as the instruction
execution time. If PCC = 0011 is selected, one machine cycle is less than 0.95
μ
s and the rated MIN. value
of 0.95
μ
s is not observed.
Note
When the clock oscillator is used, the following should be noted concerning wiring in the area in the figure
enclosed by a dotted line to prevent the influence of wiring capacitance, etc.
The wiring should be kept as short as possible.
No other signal lines should be crossed.
Keep away from lines carrying a high fluctuating current.
The oscillator capacitor grounding point should always be at the same potential as V
SS
. Do not connect
to a ground pattern carrying a high current.
A signal should be not taken from the oscillator.
#
相關PDF資料
PDF描述
UPD75116F 4-BIT SINGLE-CHIP MICROCOMPUTER
UPD75108FGF 4-BIT SINGLE-CHIP MICROCOMPUTER
UPD75116HGC 4-BIT SINGLE-CHIP MICROCOMPUTER
UPD75116HGK 4-BIT SINGLE-CHIP MICROCOMPUTER
UPD75116H 4-BIT SINGLE-CHIP MICROCOMPUTER
相關代理商/技術參數
參數描述
UPD75208 制造商:Panasonic Industrial Company 功能描述:IC
UPD753012AGC-P33-8BT-A 制造商:Renesas Electronics Corporation 功能描述:
UPD753016AGC-P29-8BT 制造商:Renesas Electronics Corporation 功能描述:
UPD75304GF-407-3B9 制造商:Renesas Electronics Corporation 功能描述:
UPD75306G182 制造商:Panasonic Industrial Company 功能描述:IC