參數資料
型號： UC1914
廠商： Texas Instruments, Inc.
元件分類： 基準電壓源/電流源
英文描述： 5V to 35V Hot Swap Power Manager
中文描述： 5V至35V的熱插拔電源管理器
文件頁數： 6/14頁
文件大?。?/td> 652K
代理商： UC1914
6
UC1914
UC2914
UC3914
Figure 2. Fault timing circuitry for the UC3914, including power limit and overcurrent.
UDG-97052
The UC3914 is to be used in conjunction with external
passive
components
and
(NMOS) to facilitate hot swap capability of application
modules. A typical application set-up is given in Fig. 9.
The term hot swap refers to the system requirement that
submodules be swapped in or out upon failure or system
modification without removing power to the operating
hardware. The integrity of the power bus must not be
compromised due to the addition of an unpowered mod-
ule. Significant power bus glitches can occur due to the
substantial initial charging current of on-board module
bypass capacitance and other load conditions (for more
information on hot swapping and power management ap-
plications, see Application Note U-151). The UC3914
provides protection by monitoring and controlling the out-
put current of an external NMOS to charge this capaci-
tance and provide load current. The addition of the
NMOS, a sense resistor, R
SENSE,
and two other resis-
tors, R1 and R2, sets the programmed maximum current
level the NMOS can source to charge the load in a con-
trolled manner. The equation for this current, I
MAX
, is:
V
V
R
SENSE
an
N-channel
MOSFET
I
MAX
CC
IMAX
=
where V
IMAX
is the voltage generated at the IMAX pin.
Analysis of the application circuit shows that V
IMAX
(with
respect to GND) can be defined as:
(
V
V
R
+
1
)
V
V
R
R
V
1
R
R
R
V
IMAX
REF
CC
REF
REF
=
+
=
+
+
1
2
2
1
2
where V
REF
is the voltage on the REF pin and whose in-
ternally generated potential is two volts below VCC. The
UC3914 also has an internal overcurrent comparator
which monitors the voltage between SENSE and VCC. If
this voltage exceeds 50mV, the comparator determines
that a fault has occurred, and a timing capacitor, C
T,
will
begin to charge. This can be rewritten as a current which
causes a fault, I
FAULT
:
mV
R
SENSE
I
FAULT
=
50
Fault Timing
Fig. 2 shows the circuitry associated with the fault timing
function of the UC3914. A typical fault mode, where the
overload comparator and current source I3 do not factor
into operation (switch S2 is open), will first be consid-
ered. Once the voltage across R
SENSE
exceeds 50mV, a
fault has occurred. This causes the timing capacitor, C
T
,
to charge with a combination of 100
μ
A (I1) plus the cur-
rent from the power limiting circuitry (I
PL
).
APPLICATION INFORMATION
相關PDF資料
PDF描述
UC2548 Primary Side PWM Controller
UC2705J High Speed Power Driver
UC2705T High Speed Power Driver
UC2844BD1R2 HIGH PERFORMANCE CURRENT MODE CONTROLLERS
UC2844B High Performance Current Mode Controllers(高性能電流模式控制器)
相關代理商/技術參數
參數描述
UC1914J 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Power Control/Management
UC19431 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision Adjustable Shunt Regulator
UC19432 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision Analog Controller
UC19432J 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision Analog Controller
UC19432J883B 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision Analog Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*