- 您現在的位置：買賣IC網 > PDF目錄272835 > TXS100ZY-P2 (POWER-ONE INC) 1-OUTPUT 120 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | TXS100ZY-P2 |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 120 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | 2.400 X 3.450 INCH, 0.500 INCH HEIGHT, 3/4 BRICK PACKAGE-14 |
| 文件頁數： | 10/27頁 |
| 文件大小： | 2635K |
| 代理商： | TXS100ZY-P2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
Product Specification
TXS Series: 75…120 A DC-DC Converters
36 to 75 V DC Input, 1.2, 1.5, 1.8, 2.0 and 2.5 V Output, 90 W to 250 W
REV. FEB 18, 2003
18 of 27
www.power-one.com
Safety Considerations
TXS modules have been designed for building into
system
applications
in
pollution
degree
2
environments
1.
The converters provide basic insulation
1 from
input to output and from input to the metallic base
plate. The insulation supports 1500 V DC electric
strength test voltage and has an insulation
resistance >50 M
.
The converters provide functional insulation
1
between output and base plate. The insulation
supports 500 V DC electric strength test voltage.
The base plate is normally floating. For safety
reasons the base plate may only be connected to
the secondary or safety ground.
If the system using the converter requires safety
agency approval, certain rules should be followed
in the design of the system. In particular, all
creepage and clearance distance requirements of
the appropriate standard should be observed. This
document refers to UL 60950, EN 60950:2000 and
CSA 60950-00 only. Specific applications may
have additional requirements.
The converter has no internal fuse. An external
fuse should be provided to protect the system. For
UL purpose the fuse needs to be UL-listed. A fuse
rating not greater than 10 A is recommended. The
user can select a lower rating fuse based upon the
inrush transient of the input filter and the maximum
input current of the converter (see page 2). Both
input tracks and the chassis ground track (if
applicable) should be capable of conducting a
current of 1.5 times the value of the fuse without
failure. The fuse should be placed in the non-
grounded input line.
The maximum specified input voltage is 100 V
DC for 100 ms. Exceeding of this voltage limit may
destroy the input stage of the converter but it will
not damage the insulation
2.
If an input supply other than SELV is used, the
components on the primary of the converter may
need to be considered as hazardous. The report:
“TXS layout considerations” on the TXS CD ROM
provides recommendations for the PCB layout
beneath the converter.
1 According to UL 60950, EN 60950:2000, CSA 60950-00
2 The creepage and clearance distance and the insulation
thickness were dimensioned for 200 V DC. The
converters have been approved for basic insulation. It is
in the responsibility of the customer to use the converter
in applications, where supplementary insulation is
required.
Definitions
The following section should help to classify the
supplying circuit of the converter. For the precise
identification of the voltage types in a system, the
relevant safety standard should be used.
Primary circuit = Circuit connected to the AC mains
which makes it hazardous per definition.
Secondary circuit = Circuit which is isolated from a
primary circuit. A battery without connection to a
primary circuit is considered to be a secondary
circuit.
SELV, ELV and TNV are secondary circuits.
SELV = User accessible secondary circuit with
U <60 V DC and no transients. An SELV circuit
remains safe even after single faults.
ELV = Basic insulated circuit with the same limits
as a SELV circuit but without protection to 60 V in
case of a single fault.
TNV = Double or reinforced insulated secondary
circuit, isolated from earth and connected to a
telecommunication network or a circuit meeting the
TNV specifications.
Table 8: Normal condition:
With
Transients
1
Without Transients
TNV-1
ELV
SELV
<60 V DC or 42.4 V AC peak
TNV-3
TNV-2
<120 V DC or 70.7 V AC peak
2
Table 9: Maximum voltage after a single fault:
With
Transients
1
Without Transients
TNV-1
ELV
SELV
<120 V continuous
3
Possibly
hazardous
<60 V, 120 V
for 0.2 s max
TNV-3
TNV-2
<120 V continuous
3
1 Up to 1.5 kV transients possible.
2 For DC voltages with overlaid AC voltages the limit:
UAC/70.7 V + UDC/120 V < 1 applies.
Exception: According deviation 2 in UL60950, the limit
80 V DC instead of 120 V DC applies in a DC-power
system for TNV2.
3 In the event of a single fault, the voltage can
rise to 1500 V for 1 ms, then fall down to 400 V within
14 ms and stay at 400 V DC over 185 ms. Limiting
curve, see figure in IEC 60950:2000.
SELV:
Safety Extra Low Voltage
ELV:
Extra Low Voltage
TNV:
Telecommunication Network Voltage
相關PDF資料 |
PDF描述 |
|---|---|
| TXS120ZA-N2V | 1-OUTPUT 180 W DC-DC REG PWR SUPPLY MODULE |
| TXS120ZA-R3H | 1-OUTPUT 180 W DC-DC REG PWR SUPPLY MODULE |
| TXS120ZY-P21V | 1-OUTPUT 144 W DC-DC REG PWR SUPPLY MODULE |
| TXS75ZY-P2R2V | 1-OUTPUT 90 W DC-DC REG PWR SUPPLY MODULE |
| TXS80ZD-3V | 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TXS10AU08AI | 制造商:TE Connectivity 功能描述: |
| TXS10AU12AI | 功能描述:環形MIL規格應變消除裝置與適配器 ADAPTER: RoHS:否 制造商:Amphenol Industrial 產品:Cable Clamps 類型:Bushing Cable Clamps MIL 類型:MIL-DTL-5015 系列:97 外殼大小:16S, 16 匹配樣式:Threaded 主體材料:Aluminum Alloy 主體類型:Straight |
| TXS10P-100A | 制造商:TOPSTEK 制造商全稱:TOPSTEK 功能描述:Anti-Magnet AC Current Sensors |
| TXS18X | 制造商:YSTONE 制造商全稱:Yellow Stone Corp 功能描述:TAPED LED LAMP |
| TXS2-1.5V | 功能描述:低信號繼電器 - PCB 2 Form C 2A 30VDC 1.5VDC RoHS:否 制造商:NEC 觸點形式:2 Form C (DPDT-BM) 觸點電流額定值: 線圈電壓:5 V 最大開關電流:1 A 線圈電流:1 A 線圈類型:Non-Latching 功耗:140 mW 端接類型:SMT 絕緣: 介入損耗: |
發布緊急采購，3分鐘左右您將得到回復。