參數資料
型號： TPS56302PWPR
英文描述： SMPS Controller
中文描述： 開關電源控制器
文件頁數： 4/34頁
文件大?。?/td> 811K
代理商： TPS56302PWPR
TPS56302
DUAL-OUTPUT LOW-INPUT-VOLTAGE
DSP POWER SUPPLY CONTROLLER WITH SEQUENCING
SLVS289A
–
MARCH 2000
–
REVISED OCTOBER 2000
4
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
DESCRIPTION
NAME
VID0
NO.
1
Voltage identification input 0. The VID pins are tri-level programming pins that set the output voltages for both
converters. The code pattern for setting the output voltage is located in table 1. The VID pins are internally pulled to
VBIAS/2, allowing floating voltage set to logic 1 (see Table 1).
Voltage identification input 1 (see VID0 pin description and Table 1).
VID1
2
SLOWST
3
Slow-start (soft start). A capacitor from pin 3 to GND sets the slow-start time for VOUT-RR and VOUT-LDO. Both supplies
will ramp-up together while tracking the slow-start voltage.
Hysteresis set pin. The hysteresis equals 2
×
(VREFB
–
VHYST).
Buffered ripple regulator reference voltage from VID network.
VHYST
4
VREFB
5
VSEN-RR
6
Ripple regulator voltage sense input. This pin is connected to the ripple regulator output. It is used to sense the ripple
regulator voltage for regulation, OVP, UVP, and power good functions. It is recommended that an RC low pass filter be
connected at this pin to filter high frequency noise.
ANAGND
7
Analog ground
Analog BIAS pin. Recommended that a 1-
μ
F capacitor be connected to ANAGND.
Output of charge pump generated through bootstrap diode. Approximately equal to VDRV + VIN
–
300 mV. Used as
supply for LDO driver and bias regulator. Recommended that a 1-
μ
F capacitor be connected to DRVGND.
Connect one end of charge pump capacitor. Recommended that a 1-
μ
F capacitor be connected from CPC1 to CPC2.
3.3 V or 5 V supply (2.8 V
–
5.5 V). It is recommended that a low ESR capacitor be connected directly from VCC to
DRVGND (bulk capacitors supplied at power stage input).
BIAS
8
VLDODRV
9
CPC1
10
VCC
11
CPC2
12
Other end of charge pump capacitor from CPC1.
VDRV
13
Regulated output of internal charge pump. Supplies DRIVE charge for the low-side MOSFET driver (5 V).
Recommended that a 10-
μ
F capacitor be connected to DRVGND.
Drive ground. Ground for FET drivers. Connect to source of low-side FET.
DRVGND
14
LOWDR
15
Low drive. Output drive to synchronous rectifier low-side FET.
BOOTLO
16
Bootstrap low. This pin connects to the junction of the high-side and low-side FETs.
Bootstrap pin. Connect a 1-
μ
F low ESR capacitor to BOOTLO to generate floating drive for the high-side FET driver.
High drive. Output drive to high-side power switching FETs
BOOT
17
HIGHDR
18
LOSENSE/
LOHIB
19
Low sense/low-side inhibit. This pin is connected to the junction of the high and low-side FETs and is used in current
sensing and the anti-cross-conduction to eliminate shoot-through current.
HISENSE
20
High current sense. For current sensing across high-side FETs, connect to the drain of the high-side FETs.
IOUTLO
21
Current sense low output. Voltage on this pin is the voltage on the LOSENSE pin when the high-side FETs are on.
INHIBIT
22
This pin inhibits the drive signals to the MOSFET drivers. The IC is in a low-current state if INHIBIT is grounded. It is
recommended that an external pullup resistor be connected to 5 V.
NGATE-LDO
23
Drives external N-channel power MOSFET to regulate LDO voltage to VREF-LDO.
VSEN
–
LDO
24
LDO voltage sense. This pin is connected to the LDO output. It is used to sense the LDO voltage for regulation, OVP,
UVP, and power good functions.
PWRGD
25
Power good. Power good signal goes high when output voltage is above 93% of VREF for both ripple regulator and
LDO. This is an open-drain output.
IOUT
26
Current signal output. Output voltage on this pin is proportional to the load current as measured across the high-side
FETs on-resistance. The voltage on this pin equals 2
×
RON
×
IOUT, where RON is the equivalent on-resistance of the
high-side FETs
OCP
27
Over current protection. Current limit trip point for ripple regulator is set with a resistor divider between the IOUT pin and
ANAGND. The trip point is typically 125 mV.
DROOP
28
Droop voltage. Voltage input used to set the amount of output voltage droop as a function of load current. The amount of
droop compensation is set with a resistor divider between the IOUT pin and ANAGND.
相關PDF資料
PDF描述
TPS5633CPWPR Voltage-Mode SMPS Controller
TPS5602IDBT Voltage-Mode SMPS Controller
TPS5602IDBTR Voltage-Mode SMPS Controller
TPS56100PWPR Voltage-Mode SMPS Controller
TPS5615CPWPR Voltage-Mode SMPS Controller
相關代理商/技術參數
參數描述
TPS56302PWPRG4 功能描述:DC/DC 開關控制器 Dual Output Low Input Vltg Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS563200DDCR 功能描述:Buck Switching Regulator IC Positive Adjustable 0.76V 1 Output 3A SOT-23-6 Thin, TSOT-23-6 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.76V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:650kHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:SOT-6 標準包裝:1
TPS563200DDCT 功能描述:Buck Switching Regulator IC Positive Adjustable 0.76V 1 Output 3A SOT-23-6 Thin, TSOT-23-6 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.76V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:650kHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:6-SOT 標準包裝:1
TPS563200EVM-652 功能描述:EVAL BOARD FOR TPS563200 制造商:texas instruments 系列:D-CAP2?，Eco-Mode?，SWIFT? 零件狀態:在售 主要用途:DC/DC，步降 輸出和類型:1，非隔離 電壓 - 輸出:1.05V 電流 - 輸出:3A 電壓 - 輸入:4.5 V ~ 17 V 穩壓器拓?fù)?降壓 頻率 - 開關:650kHz 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS563200 標準包裝:1
TPS563201DDCR 功能描述:IC REG BUCK ADJ 3A SYNC 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:在售 功能:降壓 輸出配置:正 拓?fù)?降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.768V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:580kHz 同步整流器:是 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*