參數資料
型號： TPS56302PWPR
英文描述： SMPS Controller
中文描述： 開關電源控制器
文件頁數： 12/34頁
文件大?。?/td> 811K
代理商： TPS56302PWPR
TPS56302
DUAL-OUTPUT LOW-INPUT-VOLTAGE
DSP POWER SUPPLY CONTROLLER WITH SEQUENCING
SLVS289A
–
MARCH 2000
–
REVISED OCTOBER 2000
12
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
electrical characteristics T
J
= 0
°
to 125
°
C, V
CC
= 2.8 V to 5.5 V (unless otherwise noted) (continued)
V
SENSE
–
RR
and V
SENSE
–
LDO
discharge
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
VSENSE
–
RR discharge FET current saturation
VSENSE
–
RR discharge series resistance (limits current)
VSENSE
–
RR discharge FET propagation delay time
VSENSE
–
LDO discharge FET current saturation
VSENSE
–
LDO discharge series resistance (limits current)
VSENSE
–
LDO discharge FET propagation delay time
NOTE 2. Ensured by design, not production tested.
VSENSE
–
RR = 1.5 V,
INHIBIT = 0 V,
See Note 2
5
mA
k
ns
VIN = 5.5 V
1
See Note 2
100
VSENSE
–
LDO = 3.3 V,
INHIBIT = 0 V,
See Note 2
5
mA
k
ns
VIN = 5.5 V,
1
See Note 2
100
detailed description
reference/voltage identification
The reference/voltage identification definition (VID) section consists of a temperature compensated bandgap
reference and a 2-pin voltage selection network. Both ripple regulator and LDO reference voltages are
programmed with each VID setting. The 2 VID pins are inputs to the VID selection network and are tri-level inputs
that may be set to GND, floating (V
BIAS
/2), or V
BIAS
.
The VID codes allow the controller to power both current
and future DSP products. The output voltages may also be programmed by external resistor voltage dividers
for any values not included in the VID code settings. Refer to Table 1 for the VID code settings. The output
voltages of the VID network, V
REF
–
RR
, is within 1.5% and V
REF
–
LDO
is within 2.5% of the nominal setting over
the VID range of 1.3 V to 3.3 V. The reference tolerance conditions include a junction temperature range of
–
40 C to +125 C and a V
CC
supply voltage range of 2.8 V to 5.5 V. The V
REF
–
RR
output of the reference/VID
network is indirectly brought out through a buffer to the VREFB pin. The voltage on this pin will be within 1.5%
of V
REF
–
RR
. It is not recommended to drive loads with VREFB, other than setting the hysteresis of the hysteretic
comparator, because the current drawn from VREFB sets the charging current for the slow-start capacitor. Refer
to the slow-start section of this document for additional information.
hysteretic comparator
The hysteretic comparator regulates the output voltage of the synchronous-buck converter. The hysteresis is
set by 2 external resistors and is centered around V
REF
. The two external resistors form a resistor divider from
VREFB to ANAGND, and the divided down voltage connects to the VHYST pin. The hysteresis of the
comparator will be equal to twice the voltage difference that is across the VREFB and VHYST pins. The
propagation delay from the comparator inputs to the driver outputs is 250 ns maximum. The maximum
hysteresis setting is 60 mV.
low-side driver
The low-side driver is designed to drive low r
DS(on)
logic-level N-channel MOSFETs. The current rating of the
driver is 2-A typical, source and sink. The bias to the low-side driver is internally connected to the regulated
synchronous charge pump output.
high-side driver
The high-side driver is designed to drive low r
DS(on)
logic-level N-channel MOSFETs. The current rating of the
driver is 2 amps typical, source and sink. The high-side driver can be configured either as a floating bootstrap
driver or as a ground-reference driver. When configured as a floating driver, the bias voltage to the driver is
developed from the charge pump VDRV voltage. The internal synchronous bootstrap rectifier, connected
between the VDRV and BOOT pins, is a synchronously-rectified MOSFET for improved drive efficiency. The
maximum voltage that can be applied between the BOOT pin and ground is 14 V.
相關PDF資料
PDF描述
TPS5633CPWPR Voltage-Mode SMPS Controller
TPS5602IDBT Voltage-Mode SMPS Controller
TPS5602IDBTR Voltage-Mode SMPS Controller
TPS56100PWPR Voltage-Mode SMPS Controller
TPS5615CPWPR Voltage-Mode SMPS Controller
相關代理商/技術參數
參數描述
TPS56302PWPRG4 功能描述:DC/DC 開關控制器 Dual Output Low Input Vltg Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
TPS563200DDCR 功能描述:Buck Switching Regulator IC Positive Adjustable 0.76V 1 Output 3A SOT-23-6 Thin, TSOT-23-6 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.76V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:650kHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:SOT-6 標準包裝:1
TPS563200DDCT 功能描述:Buck Switching Regulator IC Positive Adjustable 0.76V 1 Output 3A SOT-23-6 Thin, TSOT-23-6 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.76V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:650kHz 同步整流器:是 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:6-SOT 標準包裝:1
TPS563200EVM-652 功能描述:EVAL BOARD FOR TPS563200 制造商:texas instruments 系列:D-CAP2?，Eco-Mode?，SWIFT? 零件狀態:在售 主要用途:DC/DC，步降 輸出和類型:1，非隔離 電壓 - 輸出:1.05V 電流 - 輸出:3A 電壓 - 輸入:4.5 V ~ 17 V 穩壓器拓撲:降壓 頻率 - 開關:650kHz 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS563200 標準包裝:1
TPS563201DDCR 功能描述:IC REG BUCK ADJ 3A SYNC 制造商:texas instruments 系列:D-CAP2??，Eco-Mode?? 包裝:剪切帶（CT） 零件狀態:在售 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:4.5V 電壓 - 輸入（最大值）:17V 電壓 - 輸出（最小值/固定）:0.768V 電壓 - 輸出（最大值）:7V 電流 - 輸出:3A 頻率 - 開關:580kHz 同步整流器:是 工作溫度:-40°C ~ 125°C （TJ） 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型，TSOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*