- 您現在的位置：買賣IC網 > PDF目錄385946 > TPS54611-Q1 (Texas Instruments, Inc.) 3-V TO 6-V INPUT, 6-A OUTPUT SYNCHRONOUS BUCK PWM SWITCHER WITH INTEGRATED FETs(SWIFT) PDF資料下載
參數資料
| 型號： | TPS54611-Q1 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 3-V TO 6-V INPUT, 6-A OUTPUT SYNCHRONOUS BUCK PWM SWITCHER WITH INTEGRATED FETs(SWIFT) |
| 中文描述： | 3 - V至6 V輸入，6 - A輸出同步降壓PWM開關帶有集成FET協會（SWIFT） |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 246K |
| 代理商： | TPS54611-Q1 |
SGLS266D OCTOBER 2004 REVISED DECEMBER 2004
www.ti.com
14
Table 1. Summary of the Frequency
Selection Configurations
SWITCHING
FREQUENCY
FSEL PIN
RT PIN
350 kHz, internally
set
Float or AGND
Float
550 kHz, internally
set
≥
2.5 V
Float
Externally set 280
kHz to 700 kHz
Float
R = 68 k to 180 k
Externally
synchronized
frequency(1)
Synchronization
signal
R = RT value for 80% of
external synchronization
frequency
(1)To ensure proper operation when RC filter is used between external
clock and FSEL pin, the recommended values are R
≤
1k
and
C
≤
120 pF.
Error Amplifier
The high performance, wide bandwidth, voltage error
amplifier is gain-limited to provide internal compensation
of the control loop. The user is given limited flexibility in
choosing output L and C filter components. Inductance
values of 4.7
μ
H to 10
μ
H are typical and available from
several vendors. The resulting designs exhibit good noise
and ripple characteristics, but with exceptional transient
response. Transient recovery times are typically in the
range of 10
μ
s to 20
μ
s.
PWM Control
Signals from the error amplifier output, oscillator, and
current limit circuit are processed by the PWM control
logic. Referring to the internal block diagram, the control
logic includes the PWM comparator, OR gate, PWM latch,
and portions of the adaptive dead-time and control logic
block. During steady-state operation below the current
limit threshold, the PWM comparator output and oscillator
pulse train alternately set and reset the PWM latch. Once
the PWM latch is set, the low-side FET remains on for a
minimum duration set by the oscillator pulse width. During
this period, the PWM ramp discharges rapidly to its valley
voltage. When the ramp begins to charge back up, the
low-side FET turns off and high-side FET turns on. As the
PWM ramp voltage exceeds the error amplifier output
voltage, the PWM comparator resets the latch, thus
turning off the high-side FET and turning on the low-side
FET. The low-side FET remains on until the next oscillator
pulse discharges the PWM ramp.
During transient conditions, the error amplifier output
could be below the PWM ramp valley voltage or above the
PWM peak voltage. If the error amplifier is high, the PWM
latch is never reset, and the high-side FET remains on until
the oscillator pulse signals the control logic to turn the
high-side FET off and the low-side FET on. The device
operates at its maximum duty cycle until the output voltage
rises to the regulation set-point, setting VSENSE to
approximately the same voltage as V
ref
. If the error
amplifier output is low, the PWM latch is continually reset
and the high-side FET does not turn on. The low-side FET
remains on until the VSENSE voltage decreases to a
range that allows the PWM comparator to change states.
The TPS54611TPS54616 devices are capable of sinking
current continuously until the output reaches the
regulation set-point.
If the current limit comparator trips for longer than 100 ns,
the PWM latch resets before the PWM ramp exceeds the
error amplifier output. The high-side FET turns off and the
low-side FET turns on to decrease the energy in the output
inductor and consequently decrease the output current.
This process is repeated each cycle in which the current
limit comparator is tripped.
Dead-Time Control and MOSFET Drivers
Adaptive dead-time control prevents shoot-through
current from flowing in both N-channel power MOSFETs
during the switching transitions by actively controlling the
turnon times of the MOSFET drivers. The high-side driver
does not turn on until the voltage at the gate of the low-side
FET is below 2 V. The high-side and low-side drivers are
designed with 300 mA source and sink capability to quickly
drive the power MOSFETs gates. The low-side driver is
supplied from VIN, while the high-side drive is supplied
from the BOOT pin. A bootstrap circuit uses an external
BOOT capacitor and internal 2.5-
bootstrap switch
connected between the VIN and BOOT pins. The
integrated bootstrap switch improves drive efficiency and
reduces external component count.
Overcurrent Protection
Cycle-by-cycle current limiting is achieved by sensing the
current flow through the high-side MOSFET and a
differential amplifier with preset overcurrent threshold. The
high-side MOSFET is turned off within 200 ns of reaching
the current limit threshold. A 100-ns leading edge blanking
circuit prevents false tripping of current limit. Current limit
detection occurs only when current flows from VIN to PH
when sourcing current to the output filter. Load protection
during current sink operation is provided by thermal
shutdown.
Thermal Shutdown
The device uses the thermal shutdown to turn off the power
MOSFETs and disable the controller if the junction
temperature exceeds 150
°
C. The device is released from
shutdown when the junction temperature decreases to
10
°
C below the thermal shutdown trip point, and starts up
under control of the slow-start circuit. Thermal shutdown
provides protection when an overload condition is
sustained for several milliseconds. With a persistent fault
condition, the device cycles continuously: starting up by
相關PDF資料 |
PDF描述 |
|---|---|
| TPS54672EVM-222 | 6-Amp SWIFT Regulator Evaulation Module(6A SWIFT穩壓器TPS54672的評估模塊) |
| TPS54872EVM-222 | 8-Amp SWIFT Regulator Evaulation Module(8A SWIFT穩壓器TPS54872的評估模塊) |
| TPS54972EVM-222 | 9-Amp SWIFT Regulator Evaulation Module(9A SWIFT穩壓器TPS54972的評估模塊) |
| TPS54673EVM | 6-Amp SWIFT Regulator With Disabled Sink During Start-Up Evaulation Module(帶上電時禁止吸收電流功能的6A SWIFT穩壓器TPS54673的評估模塊) |
| TPS54683EVM-225 | 8-Amp SWIFT Regulator With Disabled Sink During Start-Up Evaulation Module(帶上電時禁止吸收電流功能的8A SWIFT穩壓器TPS54873的評估模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS54612 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-V TO 6-V INPUT, 6-A OUTPUT SYNCHRONOUS BUCK PWM SWITCHER WITH INTEGRATED FETs |
| TPS54612MPWPREP | 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-V TO 6-V INPUT, 6-A OUTPUT SYNCHRONOUS BUCK PWM SWITCHER WITH INTEGRATED FETs (SWIFT) |
| TPS54612PWP | 功能描述:直流/直流開關調節器 Lo-In Voltage 6A Sync Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| TPS54612PWP | 制造商:Texas Instruments 功能描述:BUCK PWM REG FET 6A SMD 54612 |
| TPS54612PWPG4 | 功能描述:直流/直流開關調節器 Lo-In Voltage 6A Sync Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。