參數資料
型號： TPS54386PWPG4
廠商： TEXAS INSTRUMENTS INC
元件分類： 穩壓器
英文描述： 7 A DUAL SWITCHING CONTROLLER, 750 kHz SWITCHING FREQ-MAX, PDSO14
封裝： GREEN, PLASTIC, HTSSOP-14
文件頁數： 9/58頁
文件大小： 1773K
代理商： TPS54386PWPG4
www.ti.com
Feedback Loop and Inductor-Capacitor (L-C) Filter Selection
TPS5438x
FB
C
COMP
11.5k W
+
Error Amplifier
0.8V
REF
BOOT
SW
+
R
COMP
Offset
f(I
DRAIN
)
PWMto
Switch
I
SLOPE
I
COMP
TPS54383
TPS54386
R
COMP
(kW)
C
COMP
(pF)
700
40
20
UDG-07012
I
COMP
-I
SLOPE
x2
SLUS774B – AUGUST 2007 – REVISED OCTOBER 2007
In the feedback signal path, the output voltage setting divider is followed by an internal gM-type error amplifier
with a typical transconductance of 30
S. An internal series connected R-C circuit from the g
M amplifier output to
ground serves as the compensation network for the converter. The signal from the error amplifier output is then
buffered and combined with a slope compensation signal before it is mirrored to be referenced to the SW node.
Here, it is compared with the current feedback signal to create a pulse-width-modulated (PWM) signal-fed to
drive the upper MOSFET switch. A simplified equivalent circuit of the signal control path is depicted in Figure 22.
NOTE:
Noise coupling from the SWx node to internal circuitry of BOOTx may impact narrow
pulse width operation, especially at load currents less than 1 A. See SW Node
Ringing for further information on reducing noise on the SWx node.
Figure 22. Feedback Loop Equivalent Circuit
A more conventional small signal equivalent block diagram is shown in Figure 23. Here, the full closed loop
signal path is shown. Because the TPS5438x contains internal slope compensation and loop compensation
components, the external L-C filter must be selected appropriately so that the resulting control loop meets criteria
for stability. This approach differs from an externally-compensated controller, where the L-C filter is generally
selected first, and the compensation network is found afterwards. To find the appropriate L and C filter
combination, the Output-to-Vc signal path plots (see the next section) of gain and phase are used along with
other design criterial to aid in finding the combinations that best results in a stable feedback loop.
Copyright 2007, Texas Instruments Incorporated
17
Product Folder Link(s): TPS54383 TPS54386
相關PDF資料
PDF描述
TPS54521RHLT SWITCHING REGULATOR, PQCC14
TPS54550PWP 9.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO16
TPS54550PWPRG4 9.5 A SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO16
TPS54610PWPR 12 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28
TPS54610PWPRG4 12 A SWITCHING REGULATOR, 762 kHz SWITCHING FREQ-MAX, PDSO28
相關代理商/技術參數
參數描述
TPS54386PWPR 功能描述:直流/直流開關調節器 DC/DC Controller RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS54386PWPRG4 功能描述:直流/直流開關調節器 3A Non-Synch Buck Converter RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
TPS54386PWPRQ1 制造商:TI 功能描述:DC/DC Controller
TPS54386-Q1 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-A DUAL NON-SYNCHRONOUS CONVERTER WITH INTEGRATED HIGH-SIDE MOSFET
TPS54386TPWPRQ1 功能描述:開關變換器、穩壓器與控制器 4.5-28V,Dual 3A Out 600kHz SD Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*