- 您現在的位置：買賣IC網 > PDF目錄365924 > TPS3600D50PWR Analog IC PDF資料下載
參數資料
| 型號： | TPS3600D50PWR |
| 英文描述： | Analog IC |
| 中文描述： | 模擬IC |
| 文件頁數： | 6/16頁 |
| 文件大小： | 214K |
| 代理商： | TPS3600D50PWR |
TPS3600D20, TPS3600D33, TPS3600D50
BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS
SLVS336 – DECEMBER 2000
6
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
NAME
BATTOK
BATTON
CEIN
CEOUT
GND
MR
MSWITCH
PFI
PFO
RESET
VBAT
VDD
VOUT
WDI
I/O
DESCRIPTION
NO.
9
6
5
10
3
11
4
7
8
13
14
2
1
12
O
O
I
O
I
I
I
I
O
O
I
I
O
I
Battery status output
Logic output/external bypass switch driver output
Chip-enable input
Chip-enable output
Ground
Manual reset input
Manual switch to force device into battery-backup mode
Power-fail comparator input
Power-fail comparator output
Active-low reset output
Backup-battery input
Input supply voltage
Supply output
Watchdog timer input
detailed description
battery freshness seal
The battery freshness seal of the TPS3600 family disconnects the backup battery from the internal circuitry until
it is needed. This ensures that the backup battery connected to V
BAT
should be fresh when the final product is
put to use. The following steps explain how to enable the freshness seal mode:
1.
Connect V
BAT
(V
BAT
>
V
BAT(min)
or V
DD(min)
)
Ground PFO
2.
3.
Connect PFI to V
DD
(PFI = V
DD
)
Connect V
DD
to power supply (V
DD
>
V
IT
) and keep connected for 5 ms < t < 35 ms
The battery freshness seal mode is disabled by the positive-going edge of RESET when V
DD
is applied.
BATTOK output
4.
This is a logic feedback of the device to indicate the status of the backup battery. The supervisor checks the
battery voltage every 200 ms with a voltage divider load of approximately 100 K
and a measure cycle on-time
of 25
μ
s. This measurement cycle starts after the reset is released. If the battery voltage V
BATT
is below the
negative-going threshold voltage V
(BOK)
, the indicator BATTOK does a high-to-low transition. Otherwise, it its
status remains to the V
OUT
level.
Table 1. Typical Values for BATTOK Indication
SUPERVISOR TYPE
VIT TYP
1.78 V
VBOK MIN
1.84 V
VBOK TYP
1.91 V
VBOK MAX
1.97 V
TPS3600x20
TPS3600x33
2.93 V
3.04 V
3.14 V
3.24 V
TPS3600x50
4.40 V
4.56 V
4.71 V
4.86 V
相關PDF資料 |
PDF描述 |
|---|---|
| TPS3606-33DGST | Analog IC |
| TPS3610T18PWR | Analog IC |
| TPS3610T25PWR | Analog IC |
| TPS3610T30PWR | Analog IC |
| TPS3610T33PWR | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS3600D50PWRG4 | 功能描述:監控電路 Battery-Backup for LP Processor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TPS3600EVM-186 | 功能描述:電源管理IC開發工具 TPS3600-186 Eval Mod RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS3600X20PW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
| TPS3600X20PWR | 制造商:TI 制造商全稱:Texas Instruments 功能描述:BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
| TPS3600X25PW | 制造商:TI 制造商全稱:Texas Instruments 功能描述:BATTERY-BACKUP SUPERVISORS FOR LOW-POWER PROCESSORS |
發布緊急采購，3分鐘左右您將得到回復。