- 您現在的位置：買賣IC網 > PDF目錄365844 > TMP93C071F (Toshiba Corporation) Quality And Reliability Assurance / Handling Precautions PDF資料下載
參數資料
| 型號： | TMP93C071F |
| 廠商： | Toshiba Corporation |
| 元件分類： | 微控制器 |
| 英文描述： | Quality And Reliability Assurance / Handling Precautions |
| 中文描述： | 質量與可靠性保證/操作注意事項 |
| 文件頁數： | 30/48頁 |
| 文件大小： | 390K |
| 代理商： | TMP93C071F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Quality and Reliability Assurance / Handling Precautions
030901
QUA-30
2002-02-20
4.1.1.2 Operating Environment
(1)
Operators must wear anti-static
clothing and conductive shoes (or a
leg or heel strap).
(2)
Operators must wear a wrist strap
grounded to earth via a resistor of about 1 M
.
Soldering irons must be grounded from iron tip to earth, and must
be used only at low voltages (6 V to 24 V).
(3)
(4)
If the tweezers you use are likely to touch the device terminals, use
anti-static tweezers and in particular avoid metallic tweezers. If a
charged device touches a low-resistance tool, rapid discharge can
occur. When using vacuum tweezers, attach a conductive chucking
pat to the tip, and connect it to a dedicated ground used especially
for anti-static purposes (suggested resistance value: 10
4
to 10
8
).
Do not place devices or their containers near sources of strong
electrical fields (such as above a CRT).
(5)
(6)
When storing printed circuit boards which have devices mounted on
them, use a board container or bag that is protected against static
charge. To avoid the occurrence of static charge or discharge due to
friction, keep the boards separate from one other and do not stack
them directly on top of one another.
(7)
Ensure, if possible, that any articles (such as clipboards) which are
brought to any location where the level of static electricity must be
closely controlled are constructed of anti-static materials.
(8)
In cases where the human body comes into direct contact with a
device, be sure to wear anti-static finger covers or gloves (suggested
resistance value: 10
8
or less).
Equipment safety covers installed near devices should have
resistance ratings of 10
9
or less.
(10) If a wrist strap cannot be used for some reason, and there is a
possibility of imparting friction to devices, use an ionizer.
(9)
(11) The transport film used in TCP products is manufactured from
materials in which static charges tend to build up. When using
these products, install an ionizer to prevent the film from being
charged with static electricity. Also, ensure that no static electricity
will be applied to the product’s copper foils by taking measures to
prevent static occurring in the peripheral equipment.
相關PDF資料 |
PDF描述 |
|---|---|
| TMP93CF76F | Quality And Reliability Assurance / Handling Precautions |
| TMP93CF77F | Quality And Reliability Assurance / Handling Precautions |
| TMP93CM40F | Quality And Reliability Assurance / Handling Precautions |
| TMP93CS20F | Quality And Reliability Assurance / Handling Precautions |
| TMP93CS32F | Quality And Reliability Assurance / Handling Precautions |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMP93CF76 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| TMP93CF76F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Quality And Reliability Assurance / Handling Precautions |
| TMP93CF77 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| TMP93CF77F | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Quality And Reliability Assurance / Handling Precautions |
| TMP93CM40 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:CMOS 16-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。