- 您現在的位置：買賣IC網 > PDF目錄69494 > TLE6712 (INFINEON TECHNOLOGIES AG) SPECIALTY ANALOG CIRCUIT, PDSO24 PDF資料下載
參數資料
| 型號： | TLE6712 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| 封裝： | PLASTIC, DSO-24 |
| 文件頁數： | 2/48頁 |
| 文件大小： | 386K |
| 代理商： | TLE6712 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
TLE 6712
Company Confidential
10
V 1.61 2001-07-13
2.4
Measurements
2.4.1
Squib Resistance Measurement
The squib resistance measurement module consists of several circuits and can be
addressed by the SPI commands 4XXX
H, 6XXXH and 7XXXH.
2.4.1.1 Precise Squib Resistance Measurement with the SPI Command
4XXX
H and 6XXXH
For a precise measurement the commands 4XXX
H and 6XXXH are used.
With the command 4XXX
H, two bias point measurements can be done. The combination
of the other two measurement eleminates the offset voltages of the OpAmp. The
command activates a bias current source of
I
Bias =5 x I
MCA. This current flows through
pin SQLx over the external resistor
R
MSR (Measurement Sense Resistor) to ground. The
pin SQLx is regulated to 8 V with the bias current.
The first measurements are used to eliminate the offset of OpAmp 1. Therefore bit b3
must be set to 0 and b2 to 0 (gain of OpAmp 1 is set to
A
1 = 10) or bit 3 to 0 and bit 2 to
1 (gain
A
1 = 30), see Chapter 3.4.1. Both inputs of the OpAmp 1 are set to its bias point
of 8 V, so that no current flows through the squib. The offset voltage
V
IO1 of OpAmp 1 is
amplified with the chosen gain factor
A
1 and reported to pin MO (Measurement Out), this
is illustrated in Figure 6.
The second measurement is done by the C A/D converter connected to the MSR pin to
determine the measurement current.
With the next two measurements the precise evaluation of the squib resistance will be
completed. In this case the SPI command 6XXX
H is used. The command 6XXXH
activates the second measurement current
I
Main. This current, IMain = M x IMCA (M = 16,
32 or 40 (set by the bits b6 and b5) see Chapter 3.4.1) flows through the squib
resistance. At the pin SQLx the currents
I
Bias and IMain are added and flow together
through the resistor
R
MSR to ground.
I)
10:
30:
V
IO1 offset voltage of OpAmp 1
A
1 gain of OpAmp 1 (10 or 30)
II)
VMO1
0.89
VCC5
×
() VIO1
–
A1
×
=
VMO1
0.86
VCC5
×
() VIO1
–
A1
×
=
VMSR1 IBias RMSR
×
=
相關PDF資料 |
PDF描述 |
|---|---|
| TLE7185E | AC MOTOR CONTROLLER, PDSO36 |
| TLE7242-2G | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| TLE8242 | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| TLE8386EL | 0.09 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO14 |
| TLI4946-2L | MAGNETIC SENSOR, PSIP3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLE6712G | 功能描述:接口 - 專用 2 Loop Firing IC RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TLE6712GNTMA1 | 制造商:Infineon Technologies AG 功能描述:Firing Circuit 24-Pin DSO 制造商:Infineon Technologies AG 功能描述:AIRBAG_RESTRAINT_IC - Tape and Reel |
| TLE6714G | 功能描述:接口 - 專用 4 Loop Firing IC RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| TLE6714GNTMA1 | 制造商:Infineon Technologies AG 功能描述:Firing Circuit 28-Pin DSO 制造商:Infineon Technologies AG 功能描述:AIRBAG_RESTRAINT_IC - Tape and Reel |
| TLE7181EM | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。