- 您現在的位置：買賣IC網 > PDF目錄69494 > TLE5012-E0742 (INFINEON TECHNOLOGIES AG) POSITION SENSOR, PDSO8 PDF資料下載
參數資料
| 型號： | TLE5012-E0742 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 模擬信號調理 |
| 英文描述： | POSITION SENSOR, PDSO8 |
| 封裝： | GREEN, PLASTIC, DSO-8 |
| 文件頁數： | 14/56頁 |
| 文件大?。?/td> | 2614K |
| 代理商： | TLE5012-E0742 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
TLE5012
Specification
Target Data Sheet
21
V 0.41, 2009-02
3.4.4
Angle Performance
After internal calculation the sensor has a remaining error, as shown in Table 7. The error value refers to BZ = 0mT
and the operating conditions given in Table 3 “Operating Range” on Page 17.
The overall angle error represents the relative angle error. This error describes the deviation to the reference line
after zero angle definition.
Autocalibration
The autocalibration enables online parameter calculation and reduces therefore the angle error due to
misalignments.
After start-up the parameters out of the fuses get loaded into flip-flops. The TLE5012 updates these parameters
after a full revolution. The update can be chosen within the Autocalibration Mode (AUTOCAL) bit. It is possible to
do the update after every 22.5°, 11.25° or after tupd.
3.4.5
Signal Processing
The signal path of the TLE5012 is depicted in Figure 11. It consists of the GMR-bridge, ADC, filter and angle
calculation. Depending on the filter configuration a different total delay time is achieved. Additional to this delay
time, the delay time of the interface has to be considered. The delay time leads to an additional angle error at
higher speeds. With enabling the prediction, the signal delay time will be reduced (Figure 12).
Figure 11
TLE5012 Signal path
At FIR_MD = 0 only raw values can be read out, due to the more time consuming angle calculation.
Table 7
Angle Performance
Parameter
Symbol
Values
Unit
Note / Test Condition
Min.
Typ.
Max.
Overall Angle Error (with auto-
calibration)
α
Err
-
0.61)
1) At 25°C, B =30 mT
1.0
°
including lifetime and
temperature drift2)3)
2) Including hysteresis error, caused by revolution direction change.
3) Only with calibrated GMR-compensation parameters of customer setup; Relative error after zero angle definition.
Overall Angle Error (without auto-
calibration)
α
Err
-
0.61)
1.6
°
including temperature
drift2)3)
X
GMR
Y
GMR
SD-
ADC
SD-
ADC
Angle
Calculation
Filter
TLE5012
Microcontroller
IF
del
t
delIF
t
upd
t
相關PDF資料 |
PDF描述 |
|---|---|
| TLE5012-E0318 | POSITION SENSOR, PDSO8 |
| TLE5203 | BRUSH DC MOTOR CONTROLLER, 4 A, PZFM7 |
| TLE5203G | BRUSH DC MOTOR CONTROLLER, 4 A, PSSO7 |
| TLE5205-2GP | BRUSH DC MOTOR CONTROLLER, 6 A, PDSO20 |
| TLE5205-2S | BRUSH DC MOTOR CONTROLLER, 6 A, PSFM7 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLE5012E0742FUMA1 | 制造商:Infineon Technologies AG 功能描述:GMR-Based Angular Sensor 8-Pin DSO |
| TLE5012FUMA1 | 制造商:Infineon Technologies AG 功能描述:GMR-Based Angular Sensor 8-Pin DSO 制造商:Infineon Technologies AG 功能描述:MAGNETIC SENSOR IC'S - Tape and Reel |
| TLE5012XT | 制造商:Infineon Technologies AG 功能描述:GMR-Based Angular Sensor 8-Pin DSO |
| TLE5025C E6747 | 功能描述:板機接口霍耳效應/磁性傳感器 HALLEFFECT IC’S RoHS:否 制造商:Honeywell 類型:Bipolar Hall-Effect Digital Position Sensor 工作電源電壓:3 V to 24 V 電源電流:3.5 mA 最大輸出電流:20 mA 工作點最小值/最大值:5 G, 55 G 最小/最大釋放點（Brp）:- 55 G, - 5 G 最大工作溫度:+ 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23 |
| TLE5025CE6747HAMA1 | 制造商:Infineon Technologies AG 功能描述:MAGNETIC SENSOR IC'S 制造商:Infineon Technologies AG 功能描述:MAGNETIC SENSOR IC'S - Ammo Pack |
發布緊急采購，3分鐘左右您將得到回復。