參數資料
型號： TJA1020
廠商： NXP Semiconductors N.V.
元件分類： 標準邏輯
英文描述： LIN transceiver
中文描述： LIN收發器
文件頁數： 6/24頁
文件大小： 105K
代理商： TJA1020
2002 Jul 17
6
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
Settingpin NSLPHIGHduringstandbymoderesultsinthe
following events:
An immediate reset of the wake-up source flag; thus
releasing the possible strong pull-down at pin TXD
before the actual mode change (after t
gotonorm
) is
performed
A change into normal slope mode if the HIGH level on
pin NSLP has been maintained for a certain time period
(t
gotonorm
) and pin TXD is HIGH
A change into low slope mode if the HIGH level on pin
NSLP has been maintained for a certain time period
(t
gotonorm
) and pin TXD is pulled LOW by the application.
In the event of a short-circuit to ground or an open-wire
on pin TXD, the LIN output remains recessive (fail safe).
A reset of the wake-up request signal on pin RXD if the
HIGH level on pin NSLP has been maintained for a
certain time period (t
gotonorm
).
Normal slope mode
In the normal slope mode the transceiver is able to
transmitandreceivedataviatheLINbusline.Thereceiver
detects the data stream at the LIN bus input pin and
transfers it via pin RXD to the microcontroller (see Fig.1):
HIGH at a recessive level and LOW at a dominant level on
the bus. The receiver has a supply voltage related
threshold with hysteresis and an integrated filter to
suppress bus line noise. The transmit data stream of the
protocol controller at the TXD input is converted by the
transmitter into a bus signal with controlled slew rate and
wave shaping to minimize EME. The LIN bus output pin is
pulled HIGH via an internal slave termination resistor. For
a master application an external resistor in series with a
diode should be connected between pin INH or BAT on
one side and pin LIN on the other side.
The normal slope mode is entered by a HIGH level on
pin TXD and a HIGH level on pin NSLP maintained for a
certain time period (t
gotonorm
), coming from the sleep or
standby mode.
The TJA1020 switches to sleep mode in case of a LOW
level on pin NSLP, maintained during a certain time period
(t
gotosleep
).
Low slope mode
The only difference between the normal slope mode and
the low slope mode is the transmitter behaviour.
In the low slope mode the transmitter output stage drives
the LIN bus line with lengthened rise and fall slopes. This
will further reduce the already outstanding EME in the
normalslopemode. The lowslopemodeisperfectly suited
for applications where transmission speed is not critical.
The mode selection is done by the LIN transceiver after a
positive edge on pin NSLP, maintained for a certain time
period (t
gotonorm
). If pin TXD is LOW at that time, the low
slope mode is entered, otherwise the normal mode is
entered. The transition to the low slope mode will be
executed during an open pin TXD (fail-safe), a short-circuit
from pin TXD to ground (fail-safe) or an intended LOW
level of pin TXD programmed by the microcontroller. The
transmitter is enabled after a LOW-to-HIGH transition on
pin TXD. In the event of a short-circuit to ground on pin
TXD, the transmitter will be disabled.
Wake-up
There are three ways to wake-up a TJA1020 which is in
sleep mode:
1.
Remote wake-up via a dominant bus state
2.
Local wake-up via a negative edge at pin NWAKE
3.
Mode change (pin NSLP is HIGH) from sleep mode to
normal slope/low slope mode.
Remote and local wake-up
A falling edge at pin NWAKE followed by a LOW level
maintained for a certain time period (t
NWAKE
) results in a
local wake-up. The pin NWAKE provides an internal
pull-up towards pin BAT.
If, during power-up, pin NWAKE is LOW for a certain
period of time (t
NWAKE
) this will also result in a local
wake-up.
A falling edge at pin LIN followed by a LOW level
maintained for a certain time period (t
BUS
) and a rising
edge at pin LIN respectively (see Fig.4) results in a remote
wake-up.
After a local or remote wake-up pin INH is activated (it
goes HIGH) and the internal slave termination resistor is
switched on. The wake-up request is indicated by a LOW
active wake-up request signal on pin RXD to interrupt the
microcontroller.
相關PDF資料
PDF描述
TJA1020_5 LIN transceiver
TL2105PIS SIP/SIE 500 NON-ISOLATED SERIES
TLD25ZEB TLD Series . 20/25A, -Brick, DC/DC Converter 48V Input Dual Output
TLD20ZGE TLD Series . 20/25A, -Brick, DC/DC Converter 48V Input Dual Output
TLD25ZED TLD Series . 20/25A, -Brick, DC/DC Converter 48V Input Dual Output
相關代理商/技術參數
參數描述
TJA1020_5 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LIN transceiver
TJA1020T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LIN transceiver
TJA1020T/CM,118 制造商:NXP Semiconductors 功能描述:TJA1020T/SO8/REEL13//CM - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC TRANSCEIVER LIN 8SOIC 制造商:NXP Semiconductors 功能描述:TJA1020 Series 12 V 4 kV ESD 20 kBaud LIN Transceiver Surface Mount - SOIC-8 制造商:NXP 功能描述:LIN transceiver; SO8 (Replacement to TJA1020T/VM)
TJA1020T/N,112 功能描述:射頻收發器 LIN TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
TJA1020T/N,118 功能描述:射頻收發器 LIN TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*