- 您現在的位置：買賣IC網 > PDF目錄371186 > TJA1020 (NXP Semiconductors N.V.) LIN transceiver PDF資料下載
參數資料
| 型號： | TJA1020 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 標準邏輯 |
| 英文描述： | LIN transceiver |
| 中文描述： | LIN收發器 |
| 文件頁數： | 19/24頁 |
| 文件大?。?/td> | 105K |
| 代理商： | TJA1020 |
2002 Jul 17
19
Philips Semiconductors
Product specification
LIN transceiver
TJA1020
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certainsurfacemountICs,butitisnotsuitableforfinepitch
SMDs. In these situations reflow soldering is
recommended.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 220
°
C for
thick/large packages, and below 235
°
C for small/thin
packages.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TJA1020_5 | LIN transceiver |
| TL2105PIS | SIP/SIE 500 NON-ISOLATED SERIES |
| TLD25ZEB | TLD Series . 20/25A, -Brick, DC/DC Converter 48V Input Dual Output |
| TLD20ZGE | TLD Series . 20/25A, -Brick, DC/DC Converter 48V Input Dual Output |
| TLD25ZED | TLD Series . 20/25A, -Brick, DC/DC Converter 48V Input Dual Output |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TJA1020_5 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LIN transceiver |
| TJA1020T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:LIN transceiver |
| TJA1020T/CM,118 | 制造商:NXP Semiconductors 功能描述:TJA1020T/SO8/REEL13//CM - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC TRANSCEIVER LIN 8SOIC 制造商:NXP Semiconductors 功能描述:TJA1020 Series 12 V 4 kV ESD 20 kBaud LIN Transceiver Surface Mount - SOIC-8 制造商:NXP 功能描述:LIN transceiver; SO8 (Replacement to TJA1020T/VM) |
| TJA1020T/N,112 | 功能描述:射頻收發器 LIN TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TJA1020T/N,118 | 功能描述:射頻收發器 LIN TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。