- 您現在的位置：買賣IC網 > PDF目錄365782 > TDA9615H (NXP SEMICONDUCTORS) Audio processor for VHS hi-fi(應用于VHS高保真的音頻處理器) PDF資料下載
參數資料
| 型號： | TDA9615H |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | Audio processor for VHS hi-fi(應用于VHS高保真的音頻處理器) |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| 封裝： | 10 X 10 X 1.75 MM, PLASTIC, SOT-307-2, QFP-44 |
| 文件頁數： | 21/44頁 |
| 文件大?。?/td> | 263K |
| 代理商： | TDA9615H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
1997 Jun 16
21
Philips Semiconductors
Preliminary specification
Audio processor for VHS hi-fi
TDA9615H
Table 30
Bit PORR; note 1
Notes
1.
Bit POR of the read byte can be used to detect the occurrence of a power-on reset situation (bit POR reads logic 1
in case the I
2
C register contents equal the POR default state). When applying bit POR this way, PORR should be
used after a power-on reset to force a reset of the POR read bit state to logic 0.
POR.
2.
Read byte (device state information)
Table 31
Bits of read byte
Table 32
Bit CALR; notes 1 and 2
Notes
1.
Bit CALR = 0 indicates the device is not calibrated. After an automatic calibration is started by setting bit CALS of the
power byte the end of calibration is signalled by this bit. If for some reason a calibration cannot be completed (e.g.
no HID signal available or hi-fi processing is in ‘playback’ mode) CALR remains logic ‘0’. If calibration is lost due to
a power-on reset situation CALR will return to logic 0 as well.
Also the envelope output (pin 39) can be used to check for end of calibration.
2.
Table 33
Bit AUTN; notes 1 and 2
Notes
1.
When hi-fi processing is in ‘playback’ mode but no hi-fi carrier input signal is detected the auto-normal function is
activated. Auto-normal overrules the ‘Output Select’ mode setting, selecting normal sound (i.e. linear audio) instead
of hi-fi. The state of this auto-normal function can be checked via bit AUTN.
The auto-normal function is only active (bit AUTN = logic 1) for hi-fi ‘playback’ mode (bit AFM = 0); during ‘record’ or
‘loop-through’ mode bit AUTN is always logic 0.
2.
PORR
MODE
DESCRIPTION
0
1
(note 2)
POR reset
reset of POR signal bit
BIT
DESCRIPTION
CALR
AUTN
POR
calibration ready; see Table 32
auto-normal; see Table 33
power-on reset; see Table 34
CALR
DESCRIPTION
0
1
device is not calibrated
device has completed auto-calibration
AUTN
DESCRIPTION
0
1
audio FM signal is detected at FM input
no audio FM signal detected; normal sound is selected instead of hi-fi
相關PDF資料 |
PDF描述 |
|---|---|
| TDA9811 | Multistandard VIF-PLL with QSS-IFand AM demodulator(帶QSS-IF和AM解調器的多標準的VIF-PLL) |
| TDA9812 | Multistandard VIF-PLL andFM-PLL/AM demodulator(多標準的VIF-PLL 和FM-PLL/AM解調器) |
| TDA9812T | Multistandard VIF-PLL and FM-PLL/AM demodulator |
| TDA9813T | VIF-PLL with QSS-IF and dual FM-PLL demodulator(帶QSS-IF和雙路FM-PLL解調器的VIF-PLL) |
| TDA9814T | Multistandard VIF-PLL with QSS-IF and dual FM-PLL/AM demodulator(帶QSS-IF和雙路FM-PLL/AM解調器的多標準VIF-PLL) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA9725 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Y/C automatic adjustment processor VHS standard |
| TDA9800 | 制造商:NXP Semiconductors 功能描述:Video/TV Circuit, TV Video Receiver Circuit, 20 Pin, Plastic, DIP |
| TDA9800T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:VIF-PLL demodulator and FM-PLL detector |
| TDA9801 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single standard VIF-PLL demodulator and FM-PLL detector |
| TDA9801/V1,112 | 功能描述:射頻無線雜項 VIF-PLL DEM./FM-PLL RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。