- 您現在的位置：買賣IC網 > PDF目錄371183 > TDA9605H (NXP SEMICONDUCTORS) Audio processor with head amplifier for VHS hi-fi PDF資料下載
參數資料
| 型號： | TDA9605H |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | Audio processor with head amplifier for VHS hi-fi |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP44 |
| 文件頁數： | 30/52頁 |
| 文件大小： | 244K |
| 代理商： | TDA9605H |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
1999 Apr 14
30
Philips Semiconductors
Product specification
Audio processor with head amplifier for VHS hi-fi
TDA9605H
7.9.7
S
TANDBY SELECT
The TDA9605H is switched in the low-power active
standby mode by setting bit STBA = 1. Most circuits are
switched inactive for reducing power consumption.
However, the RF converter, line and decoder outputs
remain active in this mode and the direct audio selections
offered via the line select function and the decoder select
function remain available. The selected output signal is
muted during the active standby mode.
The TDA9605H is switched in the minimum power passive
standby mode by setting bit STBP = 1. All circuits are
switched inactive to obtain minimum power consumption
except for the power mute circuit, the I
2
C-bus and the line
input reference buffer (i.e. the DC voltage on pins 1 to 11
remains active). When bit STBP = 1 a discharge current of
1 mA is active on pins RFCOUT, LINEL, LINER, DECL
and DECR.
Power muting ensures disturbance-free switching of the
line and RF converter outputs to and from the passive
standby mode. In the passive standby mode power muting
can be de-activated again to achieve minimum power
consumption. The calibration and I
2
C-bus registers are not
affected in the active standby or passive standby mode.
Table 34
Standby passive (bit STBP) and standby active
(bit STBA); note 1
Notes
1.
2.
X = don’t care.
Power-on reset state.
7.10
Read byte
The read byte is used for reading the device state
information.
STBP
STBA
MODE
DESCRIPTION
0
0
operating
standard operating mode:
full function; note 2
active standby mode:
reduced power
consumption
passive standby mode:
minimum power
consumption
0
1
active
standby
1
X
passive
standby
7.10.1
C
ALIBRATION READY
The completion of calibration is signalled by changing
bit CALR from logic 0 to logic 1. Bit CALR remains logic 0
if for some reason a calibration can not be completed (i.e.
no HID control signal available or the hi-fi processing is in
the playback mode). Bit CALR will also return to logic 0 if
calibration is lost due to a Power-on reset situation.
Additional information about the calibration result is
available via bit CALE. Calibration is found correct if
bit CALR = 1 and bit CALE = 0.
Pin ENVOUT can also be used to monitor calibration
(see Section 6.5).
Table 35
Calibration ready (bit CALR)
Note
1.
Power-on reset state.
7.10.2
A
UTO
-
NORMAL SELECTION
The auto-normal function is activated when no hi-fi carrier
input signal is detected in the playback mode.
The auto-normal function overrules the settings of the
output select function and selects normal sound (i.e. linear
audio) instead of hi-fi. The state of the auto-normal
function can be checked by reading bit AUTN.
The auto-normal function and therefore bit AUTN is only
valid in the playback mode. Bit AUTN is always logic 0 in
the record mode.
Table 36
Auto-normal (bit AUTN)
Note
1.
Power-on reset state.
CALR
DESCRIPTION
0
1
not calibrated; note 1
auto-calibration completed
AUTN
DESCRIPTION
0
hi-fi carrier available; audio FM signal is
detected from tape in playback mode; note 1
normal sound selected instead of hi-fi carrier;
no audio FM signal is detected from tape
1
相關PDF資料 |
PDF描述 |
|---|---|
| TDA9725 | Y/C automatic adjustment processor VHS standard |
| TDA9800 | VIF-PLL demodulator and FM-PLL detector |
| TDA9800T | VIF-PLL demodulator and FM-PLL detector |
| TDA9801 | Single standard VIF-PLL demodulator and FM-PLL detector |
| TDA9801T | Single standard VIF-PLL demodulator and FM-PLL detector |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA9610 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio FM processor for VHS hi-fi audio |
| TDA9610H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio FM processor for VHS hi-fi audio |
| TDA9614H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio processor for VHS hi-fi and linear audio |
| TDA9615 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio processor for VHS hi-fi |
| TDA9615H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio processor for VHS hi-fi |
發布緊急采購，3分鐘左右您將得到回復。