- 您現在的位置：買賣IC網 > PDF目錄371183 > TDA8939 (NXP Semiconductors N.V.) Zero dead time Class-D 7.5 A power comparator PDF資料下載
參數資料
| 型號： | TDA8939 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Zero dead time Class-D 7.5 A power comparator |
| 中文描述： | 零死時間D類7.5甲功率比較 |
| 文件頁數： | 16/21頁 |
| 文件大?。?/td> | 99K |
| 代理商： | TDA8939 |
9397 750 13023
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
Objective data sheet
Rev. 01 — 22 April 2004
16 of 21
Philips Semiconductors
TDA8939
Zero dead time Class-D 7.5 A power comparator
17. Soldering
17.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
17.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 270
°
C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
below 225
°
C (SnPb process) or below 245
°
C (Pb-free process)
–
for all BGA, HTSSON..T and SSOP..T packages
–
for packages with a thickness
≥
2.5 mm
–
for packages with a thickness < 2.5 mm and a volume
≥
350 mm
3
so called
thick/large packages.
below 240
°
C (SnPb process) or below 260
°
C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
17.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8939TH | Zero dead time Class-D 7.5 A power comparator |
| TDA9181 | Integrated multistandard comb filter |
| TDA9181P | ER 9C 7#16 2#12 PIN PLUG |
| TDA9181T | Integrated multistandard comb filter |
| TDA9605 | Audio processor with head amplifier for VHS hi-fi |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8939TH | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Zero dead time Class-D 7.5 A power comparator |
| TDA8939TH/N1,518 | 制造商:NXP Semiconductors 功能描述: |
| TDA8941 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.5 W mono Bridge Tied Load BTL audio amplifier |
| TDA8941P | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:1.5 W mono Bridge Tied Load BTL audio amplifier |
| TDA8941P/N1,112 | 功能描述:音頻放大器 1X1.5W AUDIO AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。