參數資料
型號： T89C51CC01UA-RLTIM
廠商： Atmel
文件頁數： 66/123頁
文件大?。?/td> 0K
描述： IC 8051 MCU FLASH 32K 44VQFP
標準包裝： 160
系列： AT89C CAN
核心處理器： 8051
芯體尺寸： 8-位
速度： 40MHz
連通性： CAN，UART/USART
外圍設備： POR，PWM，WDT
輸入/輸出數： 32
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 2K x 8
RAM 容量： 1.25K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 5.5 V
數據轉換器： A/D 8x10b
振蕩器型： 外部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-LQFP
包裝： 托盤
配用： AT89STK-06-ND - KIT DEMOBOARD 8051 MCU W/CAN
其它名稱： T89C51CC01UARLTIM
dsPIC33F
DS70165E-page 156
Preliminary
2007 Microchip Technology Inc.
8.2
Clock Switching Operation
Applications are free to switch between any of the four
clock sources (Primary, LP, FRC and LPRC) under
software control at any time. To limit the possible side
effects that could result from this flexibility, dsPIC33F
devices have a safeguard lock built into the switch
process.
8.2.1
ENABLING CLOCK SWITCHING
To enable clock switching, the FCKSM1 Configuration
bit in the Configuration register must be programmed to
further details.) If the FCKSM1 Configuration bit is
unprogrammed (‘1’), the clock switching function and
Fail-Safe Clock Monitor function are disabled. This is
the default setting.
The NOSC control bits (OSCCON<10:8>) do not
control the clock selection when clock switching is
disabled. However, the COSC bits (OSCCON<14:12>)
reflect the clock source selected by the FNOSC
Configuration bits.
The OSWEN control bit (OSCCON<0>) has no effect
when clock switching is disabled. It is held at ‘0’ at all
times.
8.2.2
OSCILLATOR SWITCHING
SEQUENCE
At a minimum, performing a clock switch requires this
basic sequence:
1.
If
desired,
read
the
COSC
bits
(OSCCON<14:12>) to determine the current
oscillator source.
2.
Perform the unlock sequence to allow a write to
the OSCCON register high byte.
3.
Write the appropriate value to the NOSC control
bits (OSCCON<10:8>) for the new oscillator
source.
4.
Perform the unlock sequence to allow a write to
the OSCCON register low byte.
5.
Set the OSWEN bit to initiate the oscillator
switch.
Once the basic sequence is completed, the system
clock hardware responds automatically as follows:
1.
The clock switching hardware compares the
COSC status bits with the new value of the
NOSC control bits. If they are the same, then the
clock switch is a redundant operation. In this
case, the OSWEN bit is cleared automatically
and the clock switch is aborted.
2.
If a valid clock switch has been initiated, the
LOCK
(OSCCON<5>)
and
the
CF
(OSCCON<3>) status bits are cleared.
3.
The new oscillator is turned on by the hardware
if it is not currently running. If a crystal oscillator
must be turned on, the hardware waits until the
Oscillator Start-up Timer (OST) expires. If the
new source is using the PLL, the hardware waits
until a PLL lock is detected (LOCK = 1).
4.
The hardware waits for 10 clock cycles from the
new clock source and then performs the clock
switch.
5.
The hardware clears the OSWEN bit to indicate a
successful clock transition. In addition, the NOSC
bit values are transferred to the COSC status bits.
6.
The old clock source is turned off at this time,
with the exception of LPRC (if WDT or FSCM
are enabled) or LP (if LPOSCEN remains set).
8.3
Fail-Safe Clock Monitor (FSCM)
The Fail-Safe Clock Monitor (FSCM) allows the device
to continue to operate even in the event of an oscillator
failure. The FSCM function is enabled by programming.
If the FSCM function is enabled, the LPRC internal
oscillator runs at all times (except during Sleep mode)
and is not subject to control by the Watchdog Timer.
In the event of an oscillator failure, the FSCM
generates a clock failure trap event and switches the
system clock over to the FRC oscillator. Then the
application program can either attempt to restart the
oscillator or execute a controlled shutdown. The trap
can be treated as a warm Reset by simply loading the
Reset address into the oscillator fail trap vector.
If the PLL multiplier is used to scale the system clock,
the internal FRC is also multiplied by the same factor
on clock failure. Essentially, the device switches to
FRC with PLL on a clock failure.
Note:
Primary Oscillator mode has three different
submodes (XT, HS and EC) which are
determined by the POSCMD<1:0> Config-
uration bits. While an application can
switch to and from Primary Oscillator
mode
in
software,
it
cannot
switch
between the different primary submodes
without reprogramming the device.
Note 1: The processor continues to execute code
throughout the clock switching sequence.
Timing sensitive code should not be
executed during this time.
2: Direct clock switches between any primary
oscillator mode with PLL and FRCPLL
mode are not permitted. This applies to
clock switches in either direction. In these
instances, the application must switch to
FRC mode as a transition clock source
between the two PLL modes.
相關PDF資料
PDF描述
T89C51CC01CA-SLSIM IC 8051 MCU FLASH 32K 44PLCC
T89C51CC01CA-RLTIM IC 8051 MCU FLASH 32K 44VQFP
AT91M55800A-33CI IC ARM MCU 33MHZ 176-BGA
10FMN-BMTR-A-TB CONN FMN HSNG 10POS SGL REV SMD
08FMN-BMTR-A-TB CONN FMN HOUSNG 8POS SGL REV SMD
相關代理商/技術參數
參數描述
T89C51CC01UA-SLSIM 功能描述:IC 8051 MCU FLASH 32K 44PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:AT89C CAN 標準包裝:9 系列:87C 核心處理器:8051 芯體尺寸:8-位 速度:40/20MHz 連通性:UART/USART 外圍設備:POR，WDT 輸入/輸出數:32 程序存儲器容量:32KB（32K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:0°C ~ 70°C 封裝/外殼:40-DIP（0.600"，15.24mm） 包裝:管件
T89C51CC02 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Enhanced 8-bit Microcontroller with CAN Controller and Flash
T89C51CC02_03 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:CAN Microcontrollers
T89C51CC02_0305 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Enhanced 8-bit Microcontroller with CAN Controller and Flash Memory
T89C51CC02_0312 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:CAN Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*