- 您現在的位置：買賣IC網 > PDF目錄371180 > T8536B T8535B/T8536B Quad Programmable Codec PDF資料下載
參數資料
| 型號： | T8536B |
| 元件分類： | Codec |
| 英文描述： | T8535B/T8536B Quad Programmable Codec |
| 中文描述： | T8535B/T8536B四可編程編解碼器 |
| 文件頁數： | 25/50頁 |
| 文件大?。?/td> | 929K |
| 代理商： | T8536B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Agere Systems Inc.
25
Preliminary Data Sheet
September 2001
T8535B/T8536B Quad Programmable Codec
Functional Description
(continued)
SLIC Control Capabilities
(continued)
The fast scan mode allows for a minimal data transfer
on the serial bus to monitor bits 0 and 1 of the SLIC
data memory location (159). If these two bits are wired
as inputs to the off-hook and/or ring ground detection
circuits, a convenient method of rapidly scanning for
these two functions is obtained. Bits 2 and 3 default to
outputs; thus, they are convenient to provide control of
the SLIC state. In any event, all six leads are program-
mable for maximum flexibility.
Suggested Initialization Procedures
It is suggested that upon powerup, a hardware reset be
used to set the device into a known state. The serial
interface should then be used to load the memory
addresses that differ from the default values (the write
all channels command is convenient for this function). If
other devices are controlled by the SLIC data memory
location, then it also should be loaded with a known
configuration. After the completion of this sequence,
the device is ready to be activated. Depending on the
application, the next step may either be normal opera-
tion or a set of test sequences. After the initialization of
the memory, the device and associated line card
devices can be controlled by using memory locations
130, 131, 145, 155, 156, 157, 158, 159, and 129; that
is, by supplying the PCM bus time-slot addresses,
switching the SLIC into the proper mode, and activat-
ing the codec. Within memory location 129, the codec
would normally be placed into active mode, with both
directions of the PCM bus enabled at the start of a call.
At the completion of a call, the codec should be placed
into standby mode and the PCM bus disabled. Great
caution should be used when changing the memory
while the codec is in active mode, since termination
impedances, balance impedances, and gains may
change. These changes are likely to yield undesirable
system effects. It is safe to refresh coefficients that are
known to be unchanging in the application. It is always
possible to read the memory to verify its contents with-
out deleterious effects on codec operation. Normal
operation would load the memory and perform all gain
adjustments while the codec is in standby mode.
Under no circumstances should memory above
address 162 be written, since this section of memory is
used for state data and intermediate results. Also, all
reserved addresses should not be written. Changing
this information may have deleterious effects on sys-
tem operation.
Signal Processing
Figure 21 details the signal processing functional
blocks of one channel of the codec.
0497F
* Programmable blocks.
Figure 21. Internal Signal Processing
SPEED
FROM
PCM
BUS
*
GRX1
GAIN
8 kHz
COMP
TO LIN.
TRANSFER
XLPF
GAIN
TWEAKING
GRX2
SINC
3
∑
-
D/A
1-bit
D/A
RCF
SMF
TO
SLIC
0 dB
BAL
*
32 kHz
4096 kHz
LPF
*
DIGITAL
*
*
TO
PCM
BUS
*
GAIN
GTX2
LIN.TO
COMP
YLPF
*
GAIN
TWEAKING
GTX1
SINC
3
*
FROM
SLIC
0 dB TO 24 dB
IN 5 STEPS
TRANSFER
TEQ
∑
-
A/D
LPF
*
RTZ
8 STEPS
XAG
ANALOG
CTZ
*
相關PDF資料 |
PDF描述 |
|---|---|
| T8538B | T8538B Quad Programmable Codec |
| T923CFAA | T92-Type 10 Gbits/s 1300 nm Uncooled DFB Laser Transmitter |
| T923WFAA | T92-Type 10 Gbits/s 1300 nm Uncooled DFB Laser Transmitter |
| T923FFAA | T92-Type 10 Gbits/s 1300 nm Uncooled DFB Laser Transmitter |
| TBA120T | FM IF amplifier and demodulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T8538B | 制造商:AGERE 制造商全稱:AGERE 功能描述:T8538B Quad Programmable Codec |
| T85471G | 制造商:BITECH 制造商全稱:Bi technologies 功能描述:Thick Film Super Low Profile SIP Resistor Networks |
| T85471J | 制造商:BITECH 制造商全稱:Bi technologies 功能描述:Thick Film Super Low Profile SIP Resistor Networks |
| T8550VBAAA | 制造商:Arcolectric 功能描述:2 Pole Miniature rocker switch(Curved) 制造商:Arcolectric 功能描述:Double Pole,Miniature rocker switch(Curved),Standard Body with Terminal Barrier |
| T8553VBNAK | 制造商:Arcolectric 功能描述:Double Pole,Miniature rocker switch(Curved lit),Standard Body with Terminal Barrier 制造商:Arcolectric 功能描述:2 Pole Mini rocker switch(Curved lit) |
發布緊急采購，3分鐘左右您將得到回復。