參數資料
型號： STM1404
廠商： 意法半導體
英文描述： Security Supervisor with Battery Switchover(帶電池轉換功能的安全監控器)
中文描述： 安全監控與電池切換（帶電池轉換功能的安全監控器）
文件頁數： 12/36頁
文件大?。?/td> 362K
代理商： STM1404
Pin descriptions
STM1404
12/36
Pin descriptions
See
Figure 1: Logic diagram
and
Table 2: Signal names
for a brief overview of the signals
connected to this device.
SAL, Security alarm output (open drain)
This signal can be generated when ANY of the following conditions occur:
V
INT
> V
HV
, where V
HV
= upper voltage trip limit (4.2V typ); and where V
INT
= V
CC
or
V
BAT
;
V
INT
< V
LV
, where V
LV
= lower voltage trip limit (2.0V typ); and where V
INT
= V
CC
or
V
BAT
; or
When any of the physical tamper inputs, TP
1
to TP
4
, change from their normal states to
the opposite (i.e., intrusion of a physical enclosure).
T
A
> T
H
, where T
H
is an upper temperature trip limit specified by the customer (+80°C,
+85°C, and +95°C), factory-programmed (STM1404 only);
T
A
< T
L
, where T
L
is a lower temperature trip limit specified by the customer (–25°C or
–35°C), factory-programmed (STM1404 only);
●
●
●
●
●
●
Note:
1
2
The default state of the SAL output during initial power-up is undetermined.
The alarm function will operate either with V
CC
on or when the part is internally switched
from V
CC
to V
BAT
.
TP
1
, TP
3
Physical Tamper Detect Pin set normally to High (NH). They are connected externally
through a closed switch or a high-impedance resistor to V
OUT
(in the case of STM1404A) or
V
TPU
(in the case of STM1404B/C. A tamper condition will be detected when the input pin is
pulled low (see
Figure 5
and
Figure 6 on page 10
). If not used, tie the pin to V
OUT
(for
STM1404A) or V
TPU
(for STM1404B/C).
TP
2
, TP
4
Physical Tamper Detect Pin set normally to Low (NL). They are connected externally
through a high-impedance resistor or a closed switch to V
SS
. A tamper condition will be
detected when the input pin is pulled high (see
Figure 7
and
Figure 8 on page 11
). If not
used, tie the pin to V
SS
.
Vccsw, V
CC
switch output
This output is low when V
OUT
(see
Section : V
OUT
on page 14
) is internally switched to V
CC
;
in this mode it may be used to turn on an external p-channel MOSFET switch which can
source an external device directly from V
CC
for currents greater than 80mA (bypassing the
STM1404).
This pin goes high when V
OUT
is internally switched to V
BAT
and may be used as a
“BATTERY ON” indicator.
相關PDF資料
PDF描述
STM3210B-EVAL STM32F10XXX Evaluation Board(STM32F10XXX評估板)
STM3210B-PRIMER Raisonance STM32 Primer for fun, easy evaluation and development with STM32(STM32F10XXX系列開發工具，包括Raisonance開發軟件)
STM401-2 RF POWER MODULE WIRELESS LOCAL LOOP APPLICATIONS
STM326-2 RF POWER MODULE WIRELESS LOCAL LOOP APPLICATIONS
STM351-2 RF POWER MODULE WIRELESS LOCAL LOOP APPLICATIONS
相關代理商/技術參數
參數描述
STM1404_08 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover
STM1404A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Security Supervisor with Battery Switchover
STM1404ARMBQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover
STM1404ARMCQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover
STM1404ARMDQ6F 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 V FIPS-140 security supervisor with battery switchover
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*