參數資料
型號： STLC2415
廠商： 意法半導體
英文描述： BLUETOOTH BASEBAND WITH INTEGRATED FLASH
中文描述： 藍牙基帶內置閃光燈，
文件頁數： 19/22頁
文件大?。?/td> 181K
代理商： STLC2415
19/22
STLC2415
9
The USB Transport Layer has been specified by the Bluetooth
SIG (Part H:2), and allows HCI level com-
munication between a host controller (STLC2415) and a host (e.g. PC), via a USB interface. The USB
Transport Layer is completely implemented in SW. It accepts HCI messages from the HCI Layer, prepares
it for transmission over a USB bus, and sends it to the USB Driver. It reassembles the HCI messages from
USB data received from the USB Driver, and sends these messages to the HCI Layer. The Transport Lay-
er does not interprete the contents (payload) of the HCI messages; it only examines the header.
HCI USB TRANSPORT LAYER
10 POWER CLASS1 SUPPORT
The chip can control an external power amplifier (PA). Several signals are duplicated on GPIOs for this
purpose in order to avoid digital/analog noise loops in the radio.
The Class1_En register enables the alternate functions of GPIO[15:6] to generate the signals for driving
an external PA in a Bluetooth
power class1 application.
Every bit enables a dedicated signal on a GPIO pin, as described in table 12.
Table 12. Power Class 1 Functionality
rx_on is the same as the rx_on output pin. Not rx_on is the inverted signal, in order to save components
on the application board.
PA7 to PA0 are the power amplifier control lines. They are managed, on a connection basis, by the base-
band core. The Power Level programmed for a certain Bluetooth
connection is manged by the firmware,
as specified in the Bluetooth
SIG spec.
Class1_En bit
involved GPIO
description (when class1_En bit = ‘1’)
rxon
gpio[6]
outputs a copy of rx_on pin to switch LNA/RF switch on/off
not rxon
gpio[7]
outputs an inverted copy of rx_on pin to switch LNA/RF switch on/off
PA0
gpio[8]
Bit 0 of the PA value for the current connection
PA1
gpio[9]
Bit 1 of the PA value for the current connection
PA2
gpio[10]
Bit 2 of the PA value for the current connection
PA3
gpio[11]
Bit 3 of the PA value for the current connection
PA4
gpio[12]
Bit 4 of the PA value for the current connection
PA5
gpio[13]
Bit 5 of the PA value for the current connection
PA6
gpio[14]
Bit 6 of the PA value for the current connection
PA7
gpio[15]
Bit 7 of the PA value for the current connection
相關PDF資料
PDF描述
STLC2500 BLUETOOTH⑩ SINGLE CHIP
STLC3055 WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT
STLC3055Q WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT
STLC3055QTR WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT
STLC3065 WLL SUBSCRIBER LINE INTERFACE CIRCUIT
相關代理商/技術參數
參數描述
STLC2416 制造商:STMicroelectronics 功能描述:
STLC2450 功能描述:射頻無線雜項 Eval Board STLC2450 RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel
STLC2500 制造商:STMicroelectronics 功能描述:BLUETOOTH CLS II 2.65V TO 2.85V 0.721MBPS 84TFBGA - Trays
STLC2500A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Bluetooth Single Chip
STLC2500ATR 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Bluetooth Single Chip
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*