參數資料
型號： STLC1512
廠商： 意法半導體
英文描述： NorthenLite⑩ G.lite BiCMOS Analog Front-End Circuit
中文描述： NorthenLite⑩G.lite的BiCMOS模擬前端電路
文件頁數： 10/26頁
文件大小： 329K
代理商： STLC1512
STLC1512
10/26
Input Impedance (over
process)
7,8
4.0
5
6.0
k
Measure at pin PGAIN. For all
PGA gains
Input Impedance (over
temperature)
7,9
-10%
10%
k
Measure at pin PGAIN. For all
PGA gains
Input Impedance (over process
and temperature)
7,10
3.5
5
6.5
k
Measure at pin PGAIN. For all
PGA gains
Input Signal Level @ PGAIN
0
V
cc
+0.1
V
Single ended input
Maximum Output Signal Level @
PGAOUT
11
1.1
Vpeak
Referenced to RXANG. For
minimum load impedance of
440 Ohms.
Power
12
19
mW
Active Power
<1>
<2>
The absolute gain test should be done at 30kHz, 75kHz and 120kHz with maximum output signal level of 1.1Vp.
The calculation to show how to determine the gain from the line is given in Appendix A. This appendix also shows how to cal
culate the gain variations in the application
These are chip specs only. The application specs are calculated in Appendix A.
Two tone distortion is measured with two sine waves having an amplitude given in 6. Tone one is at f1=500kHz and tone two
is at f2=300kHz, IM2 appears at 200kHz and IM3 appears ar 100kHz.
A multi-tone sine wave is used for the DS (Down Stream) Multi-tone test. (The multi-tone signal will be 91 sine waves equally
spaced from 35x4.3125kHz to 125x4.3125kHz with a peak-to-rms ratio of 5.3 and an rms voltage given in Table 6. The multi-
tone test measures the difference between the rms voltage of a single tone at the output to the rms voltage of the maximum
distortion product at the output in the frequency band between 30kHz to 120kHz.
This is the noise referred to the PGA input pin PGAIN. The input noise can be referenced to tip and ring in dBm/Hz through the
formula,
<3>
<4>
<5>
<6>
where NdB is the line noise in dBm/Hz, Vn is the input referred voltage noise of the PGA, H is the hybrid loss (9.54dB) and G
is the gain from the hybrid output to the input of the PGA. See Appendix A for calculation of G. Appendix B shows plots of the
noise performance of the entire receive path as shown in Figure 9.
These numbers are required to determine the gain variations in the application.
The input impedance specified here is the nominal value and the variation is due only to processing.
The input impedance specified here is the nominal value and the variation is due only to temperature. This variation is specified
from the nominal value at 27°C.
<10> The input impedance specified here is the nominal value with the variation due to both process and temperature.
<11> This spec is guaranteed by the distortion test.
<12> This power can not be verified independently. It can only be measured as part of the power from the RXVCC supply.
<7>
<8>
<9>
Table 6. Multi-tone sine waves
Gain Setting
2 Tone Amplitudes
Multi-tone RMS
Multi-Tone
Amplitudes
00
173 mV
66 mV
9.78 mV
01
550 mV
207 mV
30.7 mV
10
1.125 V
414 mV
61.4 mV
11
1.125 V
414 mV
61.4 mV
Table 5. PGA performance Specifications
N
dB
10
------------
V
n
2
log
G
H
+
+
=
相關PDF資料
PDF描述
STLC1 LED LAMPS CLUSTER DRIVER
STLC2150 BLUETOOTH RADIO TRANSCEIVER
STLC2415 BLUETOOTH BASEBAND WITH INTEGRATED FLASH
STLC2500 BLUETOOTH⑩ SINGLE CHIP
STLC3055 WLL & ISDN-TA SUBSCRIBER LINE INTERFACE CIRCUIT
相關代理商/技術參數
參數描述
STLC1PD 制造商:STMicroelectronics 功能描述:LED DRIVE MODULE IC - Rail/Tube
STLC2150 功能描述:射頻收發器 Bluetooth Radio Rcvr RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
STLC2410 功能描述:電信集成電路 Bluetooth Baseband RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray
STLC2410B 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:BLUETOOTH BASEBAND
STLC2411 制造商:STMicroelectronics 功能描述:BLUETOOTH CLS I 1.55V TO 1.95V 0.721MBPS 132TFBGA - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*