參數資料
型號： ST7036
廠商： Electronic Theatre Controls, Inc.
英文描述： Dot Matrix LCD Controller/Driver
中文描述： 點陣LCD控制器/驅動器
文件頁數： 14/72頁
文件大?。?/td> 864K
代理商： ST7036
ST7036
Function Description
z
System Interface
This chip has all four kinds of interface type with MPU: 4-bit bus, 8-bit bus, serial and fast I
2
C interface. 4-bit bus
or 8-bit bus is selected by DL bit in the instruction register.
During read or write operation, two 8-bit registers are used. One is data register (DR), the other is instruction
register(IR).
The data register(DR) is used as temporary data storage place for being written into or read from
DDRAM/CGRAM/ICON RAM, target RAM is selected by RAM address setting instruction. Each internal
operation, reading from or writing into RAM, is done automatically. So to speak, after MPU reads DR data, the
data in the next DDRAM/CGRAM/ICON RAM address is transferred into DR automatically. Also after MPU writes
data to DR, the data in DR is transferred into DDRAM/CGRAM/ICON RAM automatically.
The Instruction register(IR) is used only to store instruction code transferred from MPU. MPU cannot use it to
read instruction data.
To select register, use RS input pin in 4-bit/8-bit bus mode.
H
H Data Read operation (MPU reads data from DR)
V1.1
2003/12/24
14/72
Table 1. Various kinds of operations according to RS and R/W bits.
I
2
C interface
It just only could write Data or Instruction to ST7036 by the IIC Interface.
It could not read Data or Instruction from ST7036 (except Acknowledge signal).
SCL: serial clock input
SDA_IN: serial data input
SDA_OUT: acknowledge response output
Slaver address could set from “0111100” to “0111111”.
The I
2
C interface send RAM data and executes the commands sent via the I
2
C Interface. It could send data in to the RAM.
The I
2
C Interface is two-line communication between different ICs or modules. The two lines are a Serial Data line (SDA)
and a Serial Clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor. Data transfer may be
initiated only when the bus is not busy.
B
IT TRANSFER
One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of
the clock pulse because changes in the data line at this time will be interpreted as a control signal. Bit transfer is illustrated
in Fig.1.
S
TART AND STOP CONDITIONS
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line, while the clock
is HIGH is defined as the START condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is defined
as the STOP condition (P). The START and STOP conditions are illustrated in Fig.2.
S
YSTEM CONFIGURATION
The system configuration is illustrated in Fig.3.
· Transmitter: the device, which sends the data to the bus
· Master: the device, which initiates a transfer, generates clock signals and terminates a transfer
· Slave: the device addressed by a master
· Multi-Master: more than one master can attempt to control the bus at the same time without corrupting the message
RS R/W
L
L
H
Operation
L
H Read Busy Flag(DB7) and address counter (DB0 ~ DB6)
L
Data Write operation (MPU writes data into DR)
Instruction Write operation (MPU writes Instruction code into IR)
相關PDF資料
PDF描述
ST7036-0A Dot Matrix LCD Controller/Driver
ST7066 Dot Matrix LCD Controller/Driver
ST7920 ST7920
ST7920-0A ST7920
ST7920-0B ST7920
相關代理商/技術參數
參數描述
ST7036-0A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dot Matrix LCD Controller/Driver
ST7038 制造商:SITRONIX 制造商全稱:SITRONIX 功能描述:Dot Matrix LCD Controller/Driver
ST704 制造商:POLYFET 制造商全稱:Polyfet RF Devices 功能描述:SILICON GATE ENHANCEMENT MODE RF POWER VDMOSTRANSISTOR
ST7047 制造商:Pulse 功能描述:- Bulk
ST7047-001 制造商:Pulse 功能描述:- Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*