- 您現在的位置：買賣IC網 > PDF目錄372294 > ST24FW21M1 IC ACEX 1K FPGA 50K 208-PQFP PDF資料下載
參數資料
| 型號： | ST24FW21M1 |
| 英文描述： | IC ACEX 1K FPGA 50K 208-PQFP |
| 中文描述： | I2C串行EEPROM的 |
| 文件頁數： | 15/21頁 |
| 文件大?。?/td> | 152K |
| 代理商： | ST24FW21M1 |
S
S
BYTE WRITE
CONTROL
BYTE
WORD ADDR
DATA
S
PAGE WRITE
WORD ADD n
DATA n
DATA n + 1
AI01894
ACK
ACK
ACK
ACK
ACK
ACK
VCLK/WC
CONTROL
BYTE
DATA n + 7
S
ACK
ACK
Figure 12. Inhibited Write when VCLK/WC = 0
– Step 2: if the memory is busy with the internal
write cycle, no ACK will be returned and the
master goes back to Step 1. If the memory
has terminated the internal write cycle, it will
respond with an ACK, indicating that the mem-
ory is ready to receive the second part of the
instruction (the first byte of this instruction was
already sent during Step 1).
Read Operations
On delivery, the memory content is set at all "1’s"
(or FFh).
Current Address Read.
The memory has an inter-
nal byte address counter. Each time a byte is read,
this counter is incremented. For the Current Ad-
dress Read mode, following a START condition,
the master sends the Device Select code with the
RW bit set to ’1’. The memory acknowledges this
and outputs the data byte addressed by the internal
byte address counter. This counter is then incre-
mented. The master must NOT acknowledge the
data byte output and terminates the transfer with a
STOP condition.
Random Address Read.
A dummy write is per-
formed to load the address into the address
counter, see Figure 14. This is followed by a Re-
START condition send by the master and the De-
vice Select code is repeated with the RW bit set to
’1’. The memory acknowledges this and outputs the
addressed data byte. The master must NOT ac-
knowledge the data byte output and terminates the
transfer with a STOP condition.
Sequential Read.
This mode can be initiated with
either a Current Address Read or a Random Ad-
dress Read. However, in this case the master
DOES acknowledge the data byte output and the
memory continues to output the next byte in se-
quence. To terminate the stream of bytes, the
master must NOT acknowledge the last data byte
output, and MUST generate a STOP condition.
The output data is from consecutive byte ad-
dresses, with the internal byte address counter
automatically incremented after each byte output.
After a count of the last memory address, the
address counter will ’roll-over’ and the memory will
continue to output data.
Acknowledge in Read Mode.
In all read modes
the ST24xy21 wait for an acknowledge during the
9th bit time. If the master does not pull the SDA line
low during this time, the ST24xy21 terminate the
data transfer and switches to a standby state.
15/21
ST24LC21B, ST24LW21, ST24FC21, ST24FW21
相關PDF資料 |
PDF描述 |
|---|---|
| ST24FW21M6 | MAX II CPLD 570 LE 144-TQFP |
| ST24LC21BB1 | MAX 3000A CPLD 32 MC 44-PLCC |
| ST24LC21BB6 | IC ACEX 1K FPGA 100K 208-PQFP |
| ST24LC21BM1 | CONFIGURATION DEVICE, 440KBIT, TQFP32; Memory type:Configuration EPROM; Interface type:Serial; Memory size:430Kbit; Memory configuration:54KB; Frequency:16.7MHz; Temp, op. min:0(degree C); Temp, op. max:70(degree C); Case style:TQFP; RoHS Compliant: Yes |
| ST24LC21BM6 | IC CONFIG DEVICE 16MBIT 100-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST24FW21M1TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Kbit x8 Dual Mode Serial EEPROM for VESA PLUG & PLAY |
| ST24FW21M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| ST24FW21M6TR | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 Kbit x8 Dual Mode Serial EEPROM for VESA PLUG & PLAY |
| ST24GD00 | 功能描述:撥動開關 20A 2HPDP On-On RoHS:否 制造商:C&K Components 觸點形式:DPDT 開關功能:ON - ON - ON 電流額定值: 電壓額定值 AC:20 V 電壓額定值 DC:20 V 功率額定值:0.4 VA 端接類型:V-Bracket 安裝風格: 端子密封:Epoxy 觸點電鍍:Gold 照明:Not Illuminated |
| ST24JD00 | 功能描述:撥動開關 TOGGLE RoHS:否 制造商:C&K Components 觸點形式:DPDT 開關功能:ON - ON - ON 電流額定值: 電壓額定值 AC:20 V 電壓額定值 DC:20 V 功率額定值:0.4 VA 端接類型:V-Bracket 安裝風格: 端子密封:Epoxy 觸點電鍍:Gold 照明:Not Illuminated |
發布緊急采購，3分鐘左右您將得到回復。