REV. 5.0.3 LCR[7]: Baud Rate Divisors Enable Baud rate generator divisor (DLL/DLM) enable.
參數資料
型號: ST16C650ACJ44TR-F
廠商: Exar Corporation
文件頁數: 24/50頁
文件大?。?/td> 0K
描述: IC UART FIFO 32B 44PLCC
標準包裝: 500
特點: *
通道數: 1,UART
FIFO's: 32 字節
規程: 打印機,RS232,RS422,RS485
電源電壓: 2.9 V ~ 5.5 V
帶并行端口:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 44-LCC(J 形引線)
供應商設備封裝: 44-PLCC(16.59x16.59)
包裝: 帶卷 (TR)
ST16C650A
30
2.90V TO 5.5V UART WITH 32-BYTE FIFO
REV. 5.0.3
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected if LCR ≠ 0xBF.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Pins
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used for
general purpose.
Logic 0 = Force DTR# output to a logic 1 (default).
Logic 1 = Force DTR# output to a logic 0.
MCR[1]: RTS# Pins
The RTS# pin is a modem control output and may be used for automatic hardware flow control enabled by
EFR bit-6. If the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output to a logic 1 (default).
Logic 1 = Force RTS# output to a logic 0.
MCR[2]: OP1# Output
OP1# is a general purpose output.
Logic 0 = OP1# output is at logic 1 (default).
Logic 1 = OP1# output is at logic 0
MCR[3]: OP2# or IRQn Enable during PC Mode
OP2# is a general purpose output available during the Intel bus interface mode of operation. In the PC bus
mode, it enables the IRQn operation. See PC Mode section.
During Intel Bus Mode Operation:
Logic 0 = OP2# output is at logic 1 (default).
Logic 1 = OP2# output is at logic 0.
During PC Mode Operation:
Logic 0 = Disable IRQn operation (default).
Logic 1 = Enable IRQn operation.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 14.
MCR[5]: Active/Three-state Interrupt Output Enable
Logic 0 = Enable active or three-state interrupt output (default).
Logic 1 = Enable open source interrupt output mode. See Table 3 for detailed information.
相關PDF資料
PDF描述
XR16V2552IL-F IC UART FIFO 16B DUAL 32QFN
XR16L2552IM-F IC UART FIFO 16B DUAL 48TQFP
XR16L2550IL-F IC UART FIFO 16B DUAL 32QFN
ST16C2552CJ44TR-F IC UART FIFO 16B DUAL 44PLCC
ST78C36CJ44-F IC UART FIFO 16B 44PLCC
相關代理商/技術參數
參數描述
ST16C650ACP40 制造商:EXAR 制造商全稱:EXAR 功能描述:2.90V TO 5.5V UART WITH 32-BYTE FIFO
ST16C650ACQ-0A-EB 功能描述:界面開發工具 Supports C650A 48 ld TQFP, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
ST16C650ACQ48 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: 制造商:Exar Corporation 功能描述:UART, 48 Pin, Plastic, TQFP
ST16C650ACQ48-F 功能描述:UART 接口集成電路 UART W/32BYTEFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C650ACQ48TR-F 制造商:Exar Corporation 功能描述:UART 1-CH 32Byte FIFO 3.3V/5V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:ST16C650ACQ48TR-F