參數資料
型號： ST16C452CJ68TR-F
廠商： Exar Corporation
文件頁數： 26/30頁
文件大?。?/td> 0K
描述： IC UART W/PAR PORT DUAL 68PLCC
標準包裝： 250
特點： *
通道數： 2，DUART
FIFO's： 1 字節
規程： 打印機
電源電壓： 2.97 V ~ 5.5 V
帶并行端口： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 68-LCC（J 形引線）
供應商設備封裝： 68-PLCC
包裝： 帶卷 (TR)
5
ST16C452/452PS
Rev. 3.20
SYMBOL DESCRIPTION
Symbol
Pin
Signal Type
Pin Description
for either UART channels A/B or A0-A1 for the printer port,
onto D0-D7 data bus for a read cycle by an external CPU.
-IOW
36
I
Write strobe.- A logic 0 transition on this pin will transfer the
data on the internal data bus (D0-D7), as defined by either
address bits A0-A2 for UART channels A/B or A0-A1 for the
printer port, into an internal register during a write cycle from
an external CPU.
PD7-PD0
46-53
I/O
Printer Data port (Bi-directional three state) - These pins are
the eight bit, three state data bus for transferring information
to or from an external device (usually a printer). D0 is the
least significant bit. PD7-PD0 are latched during a write
cycle (output mode).
PE
67
I
Paper Empty - General purpose input or line printer paper
empty (Internal pull-up). This pin can be connected to
provide a printer out of paper indication.
RDOUT
44
O
Read Out (active high) - This pin goes to a logic 1 when the
external CPU is reading data from the 452/452PS. This
signal can be used to enable/disable external transceivers
or other logic functions.
-RESET
39
I
Master Reset (active low) - a logic 0 on this pin will reset the
internal registers and all the outputs. The UART transmitter
output and the receiver input will be disabled during reset
time. (See ST16C452/452PS External Reset Conditions for
initialization details.)
N.C.
9,61
Not Used. Should be left open.
SLCT
65
I
Select (with internal pull-up) - General purpose input or line
printer select status. Normally this pin is connected to a
printer output (active low) that indicates the ready status of
a printer, i.e., on-line and/or on-line and ready.
-SLCTIN
58
I/O
Select In (open drain, with internal pull-up) - General
purpose I/O or line printer select. This pin can be read via
Bit-3 in the printer command register, or written via bit-3 in
the printer control register. As this pin is open-drain, it can be
wire-or’d with other outputs. Normally this signal is connected
相關PDF資料
PDF描述
ST16C552CJ68TR-F IC UART FIFO 16B DUAL 68PLCC
XR68C681CJTR-F IC UART CMOS DUAL 44PLCC
ST16C2550CJ44TR-F IC UART FIFO 16B DUAL 44PLCC
XR16V2750IMTR-F IC UART FIFO 64B DUAL 48TQFP
XR88C681CJTR-F IC UART CMOS DUAL 44PLCC
相關代理商/技術參數
參數描述
ST16C452IJ68 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C452IJ68-F 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C452IJ68PS 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH PARALLEL PRINTER PORT
ST16C452IJ68PS-F 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C452IJ68TR-F 制造商:Exar Corporation 功能描述:UART 2-CH 3.3V/5V 68-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST16C452IJ68TR-F
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*