參數資料
型號： ST16C452CJ68TR-F
廠商： Exar Corporation
文件頁數： 11/30頁
文件大?。?/td> 0K
描述： IC UART W/PAR PORT DUAL 68PLCC
標準包裝： 250
特點： *
通道數： 2，DUART
FIFO's： 1 字節
規程： 打印機
電源電壓： 2.97 V ~ 5.5 V
帶并行端口： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 68-LCC（J 形引線）
供應商設備封裝： 68-PLCC
包裝： 帶卷 (TR)
19
ST16C452/452PS
Rev. 3.20
Scratchpad Register (SPR)
The ST16C452/452PS provides a temporary data
register to store 8 bits of user information.
PRINTER PORT REGISTER DESCRIPTIONS
Port Register (PR)
PR BIT 0-7:
Printer Data port (Bi-directional) - These pins are the
eight bit data bus for transferring information to or
from an external device (usually a printer). D0 is the
least significant bit. PD7-PD0 are latched during a
write cycle (output mode).
I/O Select Register (IOSEL) [452PS only]
This register is used in conjunction with the state of
BIDEN to set the direction (input/output) of the PD7-
PD0 data bus. This register is used only when BIDEN
is a logic 0.
Logic 55 (Hex) + BIDEN 0 = PD7-PD0 are set for
output mode
Logic AA (Hex) + BIDEN 0 = PD7-PD0 are set for input
mode
Status Register (SR)
This register provides the printer port input logical
states and the status of the interrupt -INTP based on
the condition of the -ACK printer port interface signal.
The logical state of these pins is dependent on exter-
nal interface signals.
SR BIT 1-0:
Not Used - initialized to a logic 1.
SR BIT-2:
Logic 0 = an interrupt is pending
When INTSEL is a logic 0, SR bit-2 basically tracks the
-ACK input interface pin (returns to a logic 1 when the
-ACK input returns to a logic 1). However when
INTSEL is a logic 1, the latched mode is selected, SR
bit-2 goes to a logic 0 with the -ACK input but does not
return to a logic 1 until the end of the read cycle, i.e.,
reading SR will set this bit to a logic 1.
Logic 1 = no interrupt is pending. (normal inactive
state)
SR BIT-3:
Logic 0 = -ERROR input is a logic 0.
Logic 1 = -ERROR input is a logic 1. (normal inactive
state)
SR BIT-4:
Logic 0 = SLCT input is a logic 0. (normal inactive
state)
Logic 1 = SLCT input is a logic 1.
SR BIT-5:
Logic 0 = PE input is a logic 0. (normal inactive state)
Logic 1 = PE input is a logic 1.
SR BIT-6:
Logic 0 = -ACK input is a logic 0.
Logic 1 = -ACK input is a logic 1. (normal inactive
state)
SR BIT-7:
Logic 0 = BUSY input is a logic 0
Logic 1 = BUSY input is a logic 1 (normal inactive
state)
Command Register (COM)
This register provides the printer port input logical
states and the status of the printer interrupt INIT,
which is based on the state of CON bit-1.
COM BIT-0:
-STROBE is a bi-directional signal with an open
source driver and internal pull-up so that it may be
wire-or’d with other outputs. COM bit-1 is used to read
status while CON bit 1 is used to set an output state.
If it is to function as an input, CON bit-1 shall be set to
a logic 1 first.
Logic 0 = -STROBE pin is a logic 1. (normal default
condition)
Logic 1 = -STROBE pin is a logic 0.
COM BIT-1:
-AutoFDXT is a bi-directional signal with an open
source driver and internal pull-up so that it may be
wire-or’d with other outputs. COM bit-1 is used to read
status while CON bit 1 is used to set an output state.
If it is to function as an input, CON bit-1 shall be set to
相關PDF資料
PDF描述
ST16C552CJ68TR-F IC UART FIFO 16B DUAL 68PLCC
XR68C681CJTR-F IC UART CMOS DUAL 44PLCC
ST16C2550CJ44TR-F IC UART FIFO 16B DUAL 44PLCC
XR16V2750IMTR-F IC UART FIFO 64B DUAL 48TQFP
XR88C681CJTR-F IC UART CMOS DUAL 44PLCC
相關代理商/技術參數
參數描述
ST16C452IJ68 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述:
ST16C452IJ68-F 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C452IJ68PS 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH PARALLEL PRINTER PORT
ST16C452IJ68PS-F 功能描述:UART 接口集成電路 DUAL UART W/PARALEL PRINTER PORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
ST16C452IJ68TR-F 制造商:Exar Corporation 功能描述:UART 2-CH 3.3V/5V 68-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST16C452IJ68TR-F
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*