- 您現在的位置：買賣IC網 > PDF目錄365727 > SST49LF004B (Silicon Storage Technology, Inc.) 4 Mbit LPC Firmware Flash PDF資料下載
參數資料
| 型號： | SST49LF004B |
| 廠商： | Silicon Storage Technology, Inc. |
| 英文描述： | 4 Mbit LPC Firmware Flash |
| 中文描述： | 4兆位LPC固件閃存 |
| 文件頁數： | 9/39頁 |
| 文件大小： | 460K |
| 代理商： | SST49LF004B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
Data Sheet
4 Mbit LPC Firmware Flash
SST49LF004B
9
2003 Silicon Storage Technology, Inc.
S71232-02-000
12/03
Clock
The LCLK pin accepts a clock input from the host controller.
Input/Output Communications
The LAD[3:0] pins are used to serially communicate cycle
information such as cycle type, cycle direction, ID selection,
address, data, and sync fields.
Input Communication Frame
The LFRAME# pin is used to indicate start of a LPC bus
cycle. The pin is also used to abort an LPC bus cycle in
progress.
Interface Mode Select
The MODE pin is used to set the interface mode. If the
mode pin is set to logic high, the device is in PP mode. If
the mode pin is set low, the device is in the LPC mode. The
mode selection pin must be configured prior to device oper-
ation. The mode pin is internally pulled down if the pin is left
unconnected.
Reset
A V
IL
on INIT# or RST# pin initiates a device reset. INIT#
and RST# pins have the same function internally. It is
required to drive INIT# or RST# pins low during a system
reset to ensure proper CPU initialization. During a Read
operation, driving INIT# or RST# pins low deselects the
device and places the output drivers, LAD[3:0], in a high
impedance state. The reset signal must be held low for a
minimum of time T
RSTP
. A reset latency occurs if a reset pro-
cedure is performed during a Program or Erase operation.
See Table 22 and Table 23, Reset Timing Parameters, for
more information. A device reset during an active Program
or Erase operation will abort the operation and memory
contents may become invalid due to data being altered or
corrupted from an incomplete Erase or Program operation.
Identification Inputs
These pins are part of a mechanism that allows multiple
devices to be attached to the same bus. The strapping of
these pins is used to identify the component. The boot
device must have ID[3:0] = 0; all subsequent devices
should use sequential count-up strapping. These pins are
internally pulled-down with a resistor between 20-100 K
.
General Purpose Inputs
The General Purpose Inputs (GPI[4:0]) can be used as dig-
ital inputs for the CPU to read. The GPI register holds the
values on these pins. The data on the GPI pins must be
stable before the start of a GPI register Read and remain
stable until the Read cycle is complete. The pins must be
driven low, V
IL
, or high, V
IH
but not left unconnected (float).
Write Protect / Top Block Lock
The Top Boot Lock (TBL#) and Write Protect (WP#) pins
are provided for hardware write protection of device mem-
ory in the SST49LF004B. The TBL# pin is used to write pro-
tect 64 KByte at the highest memory address range for the
SST49LF004B. WP# pin write protects the remaining sec-
tors in the flash memory. An active low signal at the TBL#
pin prevents Program and Erase operations of the top boot
block. When TBL# pin is held high, the hardware write pro-
tection of the top boot block is disabled. The WP# pin
serves the same function for the remaining blocks of the
device memory. The TBL# and WP# pins write protection
functions operate independently of one another. Both TBL#
and WP# pins must be set to their required protection states
prior to starting a Program or Erase operation. A logic level
change occurring at the TBL# or WP# pin during a Program
or Erase operation could cause unpredictable results.
Row / Column Select
The R/C# pin is used to control the multiplex address
inputs in Parallel Programming (PP) mode. The column
addresses are mapped to the higher internal addresses
(A
18-11
), and the row addresses are mapped to the lower
internal address (A
10-0
).
Output Enable
The OE# pin is used to gate the output data buffers in PP
mode.
Write Enable
The WE# pin is used to control the write operations in PP
mode.
No Connection
These pins are not connected internally.
相關PDF資料 |
PDF描述 |
|---|---|
| SST49LF004B-33-4C-EI | 4 Mbit LPC Firmware Flash |
| SST49LF004B-33-4C-EIE | 4 Mbit LPC Firmware Flash |
| SST49LF004B-33-4C-NH | 4 Mbit LPC Firmware Flash |
| SST49LF004B-33-4C-NHE | 4 Mbit LPC Firmware Flash |
| SST49LF040 | 4 Mbit LPC Flash |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SST49LF004B_06 | 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:4 Mbit Firmware Hub |
| SST49LF004B_10 | 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:4 Mbit Firmware Hub |
| SST49LF004B-33-4C-EI | 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:4 Mbit LPC Firmware Flash |
| SST49LF004B-33-4C-EIE | 制造商:SST 制造商全稱:Silicon Storage Technology, Inc 功能描述:4 Mbit LPC Firmware Flash |
| SST49LF004B-33-4C-NH | 功能描述:閃存 512K X 8 33ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。