- 您現在的位置：買賣IC網 > PDF目錄365725 > SST39WF1602-90-4I-B3KE (SILICON STORAGE TECHNOLOGY INC) 64 Mbit (x16) Multi-Purpose Flash Plus PDF資料下載
參數資料
| 型號： | SST39WF1602-90-4I-B3KE |
| 廠商： | SILICON STORAGE TECHNOLOGY INC |
| 元件分類： | PROM |
| 英文描述： | 64 Mbit (x16) Multi-Purpose Flash Plus |
| 中文描述： | 1M X 16 FLASH 1.8V PROM, 90 ns, PBGA48 |
| 封裝： | 6 X 8 MM, ROHS COMPLIANT, MO-210AB-1, TFBGA-48 |
| 文件頁數： | 3/29頁 |
| 文件大?。?/td> | 636K |
| 代理商： | SST39WF1602-90-4I-B3KE |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Preliminary Specifications
16 Mbit Multi-Purpose Flash Plus
SST39WF1601 / SST39WF1602
3
2006 Silicon Storage Technology, Inc.
S71297-01-000
7/06
Erase-Suspend/Erase-Resume Commands
The Erase-Suspend operation temporarily suspends a
Sector- or Block-Erase operation thus allowing data to be
read from any memory location, or program data into any
sector/block that is not suspended for an Erase operation.
The operation is executed by issuing one byte command
sequence with Erase-Suspend command (B0H). The
device automatically enters read mode typically within 20
μs after the Erase-Suspend command had been issued.
Valid data can be read from any sector or block that is not
suspended from an Erase operation. Reading at address
location within erase-suspended sectors/blocks will output
DQ
2
toggling and DQ
6
at “1”. While in Erase-Suspend
mode, a Word-Program operation is allowed except for the
sector or block selected for Erase-Suspend.
To resume Sector-Erase or Block-Erase operation which has
been suspended the system must issue Erase Resume
command. The operation is executed by issuing one byte
command sequence with Erase Resume command (30H)
at any address in the last Byte sequence.
Chip-Erase Operation
The SST39WF1601/1602 provide a Chip-Erase operation,
which allows the user to erase the entire memory array to
the “1” state. This is useful when the entire device must be
quickly erased.
The Chip-Erase operation is initiated by executing a six-
byte command sequence with Chip-Erase command
(10H) at address 5555H in the last byte sequence. The
Erase operation begins with the rising edge of the sixth
WE# or CE#, whichever occurs first. During the Erase
operation, the only valid read is Toggle Bit or Data# Polling.
See Table 6 for the command sequence, Figure 10 for tim-
ing diagram, and Figure 24 for the flowchart. Any com-
mands issued during the Chip-Erase operation are
ignored. When WP# is low, any attempt to Chip-Erase will
be ignored. During the command sequence, WP# should
be statically held high or low.
Write Operation Status Detection
The SST39WF1601/1602 provide two software means to
detect the completion of a Write (Program or Erase) cycle,
in order to optimize the system write cycle time. The soft-
ware detection includes two status bits: Data# Polling
(DQ
7
) and Toggle Bit (DQ
6
). The End-of-Write detection
mode is enabled after the rising edge of WE#, which ini-
tiates the internal Program or Erase operation.
The actual completion of the nonvolatile write is asyn-
chronous with the system; therefore, either a Data# Poll-
ing or Toggle Bit read may be simultaneous with the
completion of the write cycle. If this occurs, the system
may possibly get an erroneous result, i.e., valid data may
appear to conflict with either DQ
7
or DQ
6
. In order to pre-
vent spurious rejection, if an erroneous result occurs, the
software routine should include a loop to read the
accessed location an additional two (2) times. If both
reads are valid, then the device has completed the Write
cycle, otherwise the rejection is valid.
Data# Polling (DQ
7
)
When the SST39WF1601/1602 are in the internal Pro-
gram operation, any attempt to read DQ
7
will produce the
complement of the true data. Once the Program operation
is completed, DQ
7
will produce true data. Note that even
though DQ
7
may have valid data immediately following the
completion of an internal Write operation, the remaining
data outputs may still be invalid: valid data on the entire
data bus will appear in subsequent successive Read
cycles after an interval of 1 μs. During internal Erase oper-
ation, any attempt to read DQ
7
will produce a ‘0’. Once the
internal Erase operation is completed, DQ
7
will produce a
‘1’. The Data# Polling is valid after the rising edge of fourth
WE# (or CE#) pulse for Program operation. For Sector-,
Block- or Chip-Erase, the Data# Polling is valid after the
rising edge of sixth WE# (or CE#) pulse. See Figure 7 for
Data# Polling timing diagram and Figure 21 for a flowchart.
相關PDF資料 |
PDF描述 |
|---|---|
| SST39WF1602-90-4I-B3QE | 64 Mbit (x16) Multi-Purpose Flash Plus |
| SST39WF1602-90-4I-MBKE | 64 Mbit (x16) Multi-Purpose Flash Plus |
| SST39WF1602-90-4I-MBQE | 64 Mbit (x16) Multi-Purpose Flash Plus |
| SST39WF400A | 64 Mbit (x16) Multi-Purpose Flash Plus |
| SST39WF400A-100-4I-B3K | 64 Mbit (x16) Multi-Purpose Flash Plus |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SST39WF1602-90-4I-MBQE | 功能描述:閃存 1.65V to 1.95V 16mb Multi-Purpose 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| SST39WF400A-90-4C-B3KE | 功能描述:閃存 4M (256Kx16) 90ns 1.65-1.95V Comm RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| SST39WF400A-90-4C-B3KE-T | 功能描述:閃存 1.65 to 1.95V 4Mbit Multi-Purpose 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| SST39WF400A-90-4C-C1QE | 功能描述:閃存 4M (256Kx16) 90ns 1.65-1.95V Comm RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| SST39WF400A-90-4C-M1Q | 功能描述:閃存 256K X 16 90ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。