參數資料
型號： SST39WF1602-90-4I-B3KE
廠商： SILICON STORAGE TECHNOLOGY INC
元件分類： PROM
英文描述： 64 Mbit (x16) Multi-Purpose Flash Plus
中文描述： 1M X 16 FLASH 1.8V PROM, 90 ns, PBGA48
封裝： 6 X 8 MM, ROHS COMPLIANT, MO-210AB-1, TFBGA-48
文件頁數： 2/29頁
文件大?。?/td> 636K
代理商： SST39WF1602-90-4I-B3KE
2
Preliminary Specifications
16 Mbit Multi-Purpose Flash Plus
SST39WF1601 / SST39WF1602
2006 Silicon Storage Technology, Inc.
S71297-01-000
7/06
To meet high density, surface mount requirements, the
SST39WF1601/1602 are offered in both 48-ball TFBGA
and 48-ball WFBGA packages. See Figures 2 and 3 for
pin assignments.
Device Operation
Commands are used to initiate the memory operation func-
tions of the device. Commands are written to the device
using standard microprocessor write sequences. A com-
mand is written by asserting WE# low while keeping CE#
low. The address bus is latched on the falling edge of WE#
or CE#, whichever occurs last. The data bus is latched on
the rising edge of WE# or CE#, whichever occurs first.
The SST39WF1601/1602 also have the
Auto Low Power
mode which puts the device in a near standby mode after
data has been accessed with a valid Read operation. This
reduces the I
DD
active read current from typically 9 mA to
typically 5 μA. The Auto Low Power mode reduces the typi-
cal I
DD
active read current to the range of 2 mA/MHz of
Read cycle time. The device exits the Auto Low Power
mode with any address transition or control signal transition
used to initiate another Read cycle, with no access time
penalty. Note that the device does not enter Auto-Low
Power mode after power-up with CE# held steadily low,
until the first address transition or CE# is driven high.
Read
The Read operation of the SST39WF1601/1602 is con-
trolled by CE# and OE#, both have to be low for the sys-
tem to obtain data from the outputs. CE# is used for
device selection. When CE# is high, the chip is dese-
lected and only standby power is consumed. OE# is the
output control and is used to gate data from the output
pins. The data bus is in high impedance state when
either CE# or OE# is high. Refer to the Read cycle timing
diagram for further details (Figure 4).
Word-Program Operation
The SST39WF1601/1602 are programmed on a word-by-
word basis. Before programming, the sector where the
word exists must be fully erased. The Program operation is
accomplished in three steps. The first step is the three-byte
load sequence for Software Data Protection. The second
step is to load word address and word data. During the
Word-Program operation, the addresses are latched on the
falling edge of either CE# or WE#, whichever occurs last.
The data is latched on the rising edge of either CE# or
WE#, whichever occurs first. The third step is the internal
Program operation which is initiated after the rising edge of
the fourth WE# or CE#, whichever occurs first. The Pro-
gram operation, once initiated, will be completed within 40
μs. See Figures 5 and 6 for WE# and CE# controlled Pro-
gram operation timing diagrams and Figure 20 for flow-
charts. During the Program operation, the only valid reads
are Data# Polling and Toggle Bit. During the internal Pro-
gram operation, the host is free to perform additional tasks.
Any commands issued during the internal Program opera-
tion are ignored. During the command sequence, WP#
should be statically held high or low.
Sector/Block-Erase Operation
The Sector- (or Block-) Erase operation allows the system
to erase the device on a sector-by-sector (or block-by-
block) basis. The SST39WF1601/1602 offer both Sector-
Erase and Block-Erase modes. The sector architecture is
based on uniform sector size of 2 KWord. The Block-Erase
mode is based on uniform block size of 32 KWord. The
Sector-Erase operation is initiated by executing a six-byte
command sequence with Sector-Erase command (30H)
and sector address (SA) in the last bus cycle. The Block-
Erase operation is initiated by executing a six-byte com-
mand sequence with Block-Erase command (50H) and
block address (BA) in the last bus cycle. The sector or block
address is latched on the falling edge of the sixth WE#
pulse, while the command (30H or 50H) is latched on the
rising edge of the sixth WE# pulse. The internal Erase
operation begins after the sixth WE# pulse. The End-of-
Erase operation can be determined using either Data#
Polling or Toggle Bit methods. See Figures 10 and 11 for
timing waveforms and Figure 24 for the flowchart. Any
commands issued during the Sector- or Block-Erase oper-
ation are ignored. When WP# is low, any attempt to Sector-
(Block-) Erase the protected block will be ignored. During
the command sequence, WP# should be statically held
high or low.
相關PDF資料
PDF描述
SST39WF1602-90-4I-B3QE 64 Mbit (x16) Multi-Purpose Flash Plus
SST39WF1602-90-4I-MBKE 64 Mbit (x16) Multi-Purpose Flash Plus
SST39WF1602-90-4I-MBQE 64 Mbit (x16) Multi-Purpose Flash Plus
SST39WF400A 64 Mbit (x16) Multi-Purpose Flash Plus
SST39WF400A-100-4I-B3K 64 Mbit (x16) Multi-Purpose Flash Plus
相關代理商/技術參數
參數描述
SST39WF1602-90-4I-MBQE 功能描述:閃存 1.65V to 1.95V 16mb Multi-Purpose 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
SST39WF400A-90-4C-B3KE 功能描述:閃存 4M (256Kx16) 90ns 1.65-1.95V Comm RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
SST39WF400A-90-4C-B3KE-T 功能描述:閃存 1.65 to 1.95V 4Mbit Multi-Purpose 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
SST39WF400A-90-4C-C1QE 功能描述:閃存 4M (256Kx16) 90ns 1.65-1.95V Comm RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
SST39WF400A-90-4C-M1Q 功能描述:閃存 256K X 16 90ns RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*