- 您現在的位置：買賣IC網 > PDF目錄10901 > SI3015-BS (Silicon Laboratories Inc)IC ISOMODEM LINE-SIDE DAA 16SOIC PDF資料下載
參數資料
| 型號： | SI3015-BS |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 19/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ISOMODEM LINE-SIDE DAA 16SOIC |
| 標準包裝： | 48 |
| 系列： | ISOmodem® |
| 數據格式： | V.90 |
| 波特率： | 2.4k |
| 電源電壓： | 3.3V，5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
Si3038
26
Rev. 2.01
GPIO Pin Status register.
The Si3038 can also be programmed to wake up on
events due to GPIO_A and GPIO_B.
DTMF Dialing
In CTR21 dc termination mode, the DIAL bit in
register 62h should be set during DTMF dialing if the
LCS[3:0] bits are less than 6. Setting this bit increases
headroom for large signals. This bit should not be used
during normal operation or if LCS[3:0] greater than 5.
In Japan dc termination mode the Si3038 attenuates the
transmit
output
by
1.7 dB
to
meet
headroom
requirements. This attenuation can be removed when
DTMF dialing is desired in this mode. When in the FCC
dc termination mode, the FJM bit in register 62h will
enable the Japan dc termination mode without the
1.7 dB attenuation. Increased distortion may be
observed, which is acceptable during DTMF dialing.
After DTMF dialing is complete, the attenuation should
be enabled by setting the Japan dc termination mode
DCT[1:0]=01b. The FJM bit has no effect in Japan dc
termination mode.
Higher DTMF levels may also be achieved if the
amplitude is increased and the peaks of the DTMF
signal are clipped at digital full scale (as opposed to
wrapping). Clipping the signal will produce some
distortion and intermodulation of the signal. Generally,
somewhat increased distortion (up to 10%) is
acceptable during DTMF signaling. Several dB higher
DTMF levels can be achieved with this technique,
compared with a digital full scale peak signal.
Pulse Dialing
Pulse dialing is accomplished by going off- and on-hook
to generate make and break pulses. The nominal rate is
10 pulses per second. Some countries have very tight
specifications for pulse fidelity, including make and
break times, make resistance, and rise and fall times. In
a traditional solid-state dc holding circuit, there are a
number of issues in meeting these requirements.
The Si3038 dc holding circuit has active control of the
on-hook and off-hook transients to maintain pulse
dialing fidelity.
Spark quenching requirements in countries such as
Italy, the Netherlands, South Africa, and Australia deal
with the on-hook transition during pulse dialing. These
tests provide an inductive dc feed, resulting in a large
voltage spike. This spike is caused by the line
inductance and the sudden decrease in current through
the loop when going on-hook. The traditional way of
dealing with this problem is to put a parallel RC shunt
across the hookswitch relay. The capacitor is large
(~1 uF, 250 V) and relatively expensive. In the Si3038,
the OHS bit in register 5Ch can be used to slowly ramp
down the loop current to pass these tests without
requiring additional components.
Billing Tone Detection
"Billing tones" or "Metering Pulses" generated by the
central office can cause modem connection difficulties.
The billing tone is typically either a 12 KHz or 16 KHz
signal and is sometimes used in Germany, Switzerland,
and South Africa. Depending on line conditions, the
billing tone may be large enough to cause major errors
related to the modem data. The Si3038 chipset has a
feature which allows the device to remain off-hook
during billing tones and provide feedback as to whether
a billing tone has occurred and when it ends.
Billing tone detection is enabled by setting the BTE bit
(register 5Ch). Billing tones less than 1.1 VPK on the line
will be filtered out by the low pass digital filter on the
Si3038. The ROV bit is set when a line signal is greater
than 1.1 VPK, indicating an ADC overload condition. The
BTD bit is set when a line signal (billing tone) is large
enough to excessively reduce the internal power supply
of the line-side device (Si3014). When the BTD bit is
set, the dc termination is released to maintain an off
hook condition, and the line is presented with an 800
dc impedance.
The OVL bit should be monitored (polled) following a
billing tone detection. When the OVL bit returns to zero,
indicating that the billing tone has passed, the BTE bit
should be written to zero to return the dc termination to
its original state. It will take approximately one second to
return to normal dc operating conditions. The BTD and
ROV bits are sticky, and they must be written to zero to
be reset. After the BTE, ROV, and BTD bits are all
cleared, the BTE bit can be set to reenable billing tone
detection.
Certain line events, such as an off-hook event on a
parallel phone or a polarity reversal, may trigger the
ROV or the BTD bits, after which the billing tone detector
must be reset. The user should look for multiple events
before qualifying whether billing tones are actually
present.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C54T-XTE/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54T-RC/SS | IC MCU OTP 512X12 20SSOP |
| VE-262-IX-F2 | CONVERTER MOD DC/DC 15V 75W |
| PIC16C54T-RC/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54T-RCI/SS | IC MCU OTP 512X12 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3015-BSR | 功能描述:電信線路管理 IC CONTACT SILICON LABS FOR AVAILABILITY RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3015-E-FSR | 制造商:Silicon Laboratories Inc 功能描述: |
| Si3015-F-FS | 功能描述:電信線路管理 IC Si2400 ISOmodem Line-Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3015-F-FSR | 制造商:Silicon Laboratories Inc 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 16SOIC - Tape and Reel 制造商:Silicon Laboratories 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R |
| SI3015-FS | 功能描述:IC ISOMODEM LINE-SIDE DAA 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:ISOmodem® 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
發布緊急采購，3分鐘左右您將得到回復。