參數資料
型號： SI3012-KT
廠商： Electronic Theatre Controls, Inc.
英文描述： 3.3 V FCC/JATE DIRECT ACCESS ARRANGEMENT
中文描述： 3.3伏催化裂化/ JATE直接訪問安排
文件頁數： 29/64頁
文件大小： 1740K
代理商： SI3012-KT
Si3038
Rev. 2.01
29
near a transition level. The LCS value is a rough
approximation of the loop current, and the designer is
advised to use this value in a relative means rather than
an absolute value.
This feature enables the modem to determine if an
additional line has “picked up” while the modem is
transferring information. In the case of a second phone
going off-hook, the loop current falls approximately 50%
and is reflected in the value of the LCS bits.
Overload Detection
The Si3038 can detect if an overload condition is
present which may damage the DAA circuit. The DAA
may be damaged if excessive line voltage or loop
current is sustained.
In FCC and Japan dc termination modes, an LCS[3:0]
value of 1111b means the loop current is greater than
120 mA indicating the DAA is drawing excessive loop
current.
In CTR21 mode, 120 mA of loop current is not possible
due to the current limit circuit. In this dc termination
mode, an LCS[3:0] value of 1000b (8 decimal) or
greater indicates an excessive loop current condition.
Analog Output
The Si3038 supports an analog output (AOUT) for
driving the call progress speaker. AOUT is an analog
signal comprised of a mix of the transmit and receive
signals.
The AOUT level can be adjusted via the ATM and ARM
bits in control register 5Ch. The transmit portion of
AOUT can be set to –20 dB, –26 dB, –32 dB, or mute.
The receive portion of AOUT can be set to 0 dB, –6 dB,
–12 dB, or mute. Figure 20 on page 19 illustrates a
recommended application circuit. Note that in the
configuration shown, the LM386 provides a gain of 26
dB. Additional gain adjustments may be made by
varying the voltage divider created by R1 and R3.
Gain Control
The Si3038 supports multiple gain and attenuation
settings in register 46h/48h for the receive and transmit
paths, respectively. The receive path can support gains
of 0, 3, 6, 9, and 12 dB, as selected by ADC[3:1] bits.
The receive path can also be muted by setting bit 7. The
transmit path can support attenuations of 0, 3, 6, 9, and
12 dB, as selected by DAC[3:1] bits. The transmit path
can also be muted by setting bit 15.
Filter Selection
The Si3038 supports additional filter selections for the
receive and transmit signals. The IIRE bit of register
5Ch, when set, enables the IIR filters. This filter
provides a much lower, however non-linear, group delay
than the default FIR filters.
In-Circuit Testing
The Si3038’s advanced design provides the modem
manufacturer with increased ability to determine system
functionality during production line tests, as well as user
diagnostics. Several loopback modes exist allowing
increased coverage of system components.
The loopback mode allows the data pump to provide a
digital input test pattern on SDATA_IN and receive a
corresponding digital test pattern back on SDATA_OUT.
To enable this mode, set L1B[2:0](L2B[2:0])=101 in
register 56h. In this mode, the isolation barrier is
actually being tested. The digital stream is delivered
across the isolation capacitors, C1 and C2 of Figure 19
on page 16, to the line-side device and returned across
the same barrier.
The digital DAC loopback mode allows data to be sent
on the digital path from SDATA_IN to the digital section
of DAC to ADC to SDATA_OUT. This loopback mode is
used when the line-side chip is in power-down mode. To
enable this mode, set L1B[2:0](L2B[2:0]) = 011 in
register 56h.
The remote analog loopback mode allows an external
device to drive the receive pins of the line-side chip and
receive the signal from the transmit pins. This mode
allows testing of external components connecting the
RJ-11 jack (TIP and RING) to the line side of the
Si3014. To enable this mode, set L1B2:0(L2B2:0) = 100
in register 56h.
The ADC loopback mode allows an external device to
drive the receive pins of the Si3014. The signal is then
digitized on the Si3014 and sent to the Si3024, which
sends the data back to the Si3014. The signal is then
converted back to analog. The external device receives
the signal on the transmit pins. This mode allows testing
of the Si3038s converters and external devices between
the Si3014 and RJ-11 jack. To enable this mode, set the
L1B[2:0](L2B[2:0]) = 001.
The final two testing modes, local analog loopback and
external analog loopback, allow the system to test the
basic operation of the converters on the line side and
the functionality of the external components. In local
analog loopback mode, the AC’97 controller provides a
digital test waveform on SDATA_OUT. This data is
passed across the isolation barrier, converted to analog,
internally looped to the receive path, converted to
digital, passed back across the isolation barrier, and
presented to the AC’97 controller. To enable local and
analog loopback, set L1B2:0 (L2B2:0) = 010. External
analog loopback mode allows the system to test
external components by passing converted data (from
相關PDF資料
PDF描述
SI3035 3.3 V FCC/JATE DIRECT ACCESS ARRANGEMENT
SI3034 DESICCANT CLAY, 30G, PK400; RoHS Compliant: NA
SI3036 Masking Tape; Tape Backing Material:Crepe Paper; Width:24mm; Roll Length:55m; Adhesive Material:Rubber; Color:Natural; Leaded Process Compatible:No; Pack Quantity:1 RoHS Compliant: Yes
SI3038 Duct Tape; Tape Backing Material:PVC; Width:2"; Roll Length:50yard; Color:Gray; Features:Temperature-stable adhesive, Tears easily and evently by hand, leaves no stciky residue when removed RoHS Compliant: Yes
SI3044 3M 401Q IMPERIAL WETORDRY SHEET
相關代理商/技術參數
參數描述
SI-3012LU 制造商:SANKEN 制造商全稱:Sanken electric 功能描述:Surface-Mount, Low Current Consumption, Low Dropout Voltage Dropper Type
SI-3012LU-TL 制造商:Sanken Electric Co Ltd 功能描述:IC REG LDO ADJ 0.25A SOT89-5
SI-30135-F 功能描述:CONN MAGJACK 4PORT SHLD 10/100BT RoHS:是 類別:連接器，互連式 >> 模塊 - 帶磁性元件的插座 系列:MagJack® ST SI-30000 標準包裝:63 系列:Mag45 連接器類型:RJ45 端口數:1 行數:1 安裝類型:面板安裝，通孔，直角 速度:10/100 Base-T 板上方高度:0.555"（14.10mm） LED 顏色:綠 - 綠 每一插座芯體的數目:5 屏蔽:屏蔽 翼片方向:上 特點:板鎖 包裝:托盤
SI3014 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GLOBAL MC 97 SILICON DAA
SI-30140-F 制造商:Bel Fuse 功能描述:- Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*