參數資料
型號: SI2439-A-FM
廠商: Silicon Laboratories Inc
文件頁數: 22/70頁
文件大?。?/td> 0K
描述: IC ISOMODEM 33.6KBPS 38-QFN
標準包裝: 364
系列: *
Si2494/39
Rev. 1.0
29
Vn
Result code type (see Table 14 on page 49).
V0
Numeric result codes.
V1
Verbal result codes
Xn
Call Progress Monitor (CPM)—This command controls which CPM signals are monitored
and reported to the host from the Si2494/39. (See Table 14 on page 49.)
X0
Basic results; disable CPM—Blind dial (does not wait for dial tone). CONNECT message
does not include speed.
X1
Extended results; disable CPM—Blind dial. CONNECT message includes speed.
X2
Extended results and detect dial tone only—Add dial tone detection to X1 mode. Does not
blind dial.
X3
Extended results and detect busy only—Add busy tone detection to X1 mode.
X4
Extended results, full CPM—Full CPM enabled, CONNECT message includes speed.
X5
Extended results—Full CPM enabled including ringback detection. Adds ringback detection
to X4 mode.
Yn
Long space disconnect—Modem hangs up after 1.5 seconds or more of continuous space
while on-line.
Y0
Disable.
Y1
Enable.
Z
Hard Reset—This command is functionally equivalent to pulsing the RESET pin low. (See
:E
Read from serial EEPROM.
:I
Interrupt Read—This command causes the ISOmodem to report the lower 8 bits of the
interrupt register I/O Control 0 (U70). The CID, OCD, PPD, and RI bits also are cleared, and
the INT pin (INT bit in parallel mode) is deactivated on this read.
:M
Write to serial EEPROM.
:P
Program RAM Write—This command is used to upload firmware supplied by Silicon Labs to
the Si2494/39. The format for this command is AT:Paaaa,xxxx,yyyy,.... where aaaa is the first
address in hexadecimal and xxxx,yyyy,.... is data in hexadecimal. Only one :P command is
allowed per AT command line. No other commands can be concatenated in the :P command
line. This command is only for use with special files provided by Silicon Laboratories. Do not
attempt to use this command for any other purpose.
:R
User-Access Register Read—This command allows the user to read from the user-access
registers (see "6. User-Access Registers (U-Registers)" on page 54). The format is “AT:Raa”,
where:
aa = user-access address in hexadecimal.
The “AT:R” command causes all the U- registers to be displayed.
:U
User-Access Register Write—This command allows the user to write to the 16-bit user-
access registers. (See page page 54.) The format is “AT:Uaa,xxxx,yyyy,zzzz,...” where
aa = user-access address in hexadecimal.
xxxx = Data in hexadecimal to be written to location aa.
yyyy = Data in hexadecimal to be written to location (aa + 1).
zzzz = Data in hexadecimal to be written to location (aa + 2).
etc.
Table 10. Basic AT Command Set (Command Defaults in Bold) (Continued)
Command
Action
相關PDF資料
PDF描述
PIC16C62B/JW IC MCU EPROM 2KX14 PWM 28CDIP
PIC16C57C/JW IC MCU EPROM 2KX12 28CDIP
VI-2NK-IX-F2 CONVERTER MOD DC/DC 40V 75W
PIC16C55A/JW IC MCU EPROM 512X12 28CDIP
VI-2N0-IX-F3 CONVERTER MOD DC/DC 5V 75W
相關代理商/技術參數
參數描述
Si2439-A-FM18-EVB 功能描述:網絡開發工具 38pin Si2439+ Si3018 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
SI2439-A-FMR 制造商:Silicon Laboratories Inc 功能描述:33.6 KBPS ISOMODEM + VOICE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC ISOMODEM 33.6KBPS 38-QFN
SI2439-A-GM 功能描述:IC ISOMODEM 33.6KBPS 38-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:* 標準包裝:25 系列:- 數據格式:V.21,V.22,V.23,V.29,V.32,V.34,V.90,V.92,Bell 103,Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574
SI2439-A-GMR 制造商:Silicon Laboratories Inc 功能描述:33.6 KBPS ISOMODEM + VOICE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC ISOMODEM 33.6KBPS 38-QFN
SI2456 制造商:SILABS 制造商全稱:SILABS 功能描述:V.90, V.34, V.32BIS ISOMODEM⑩ WITH INTEGRATED GLOBAL DAA