參數資料
型號： SC16C654BIEC
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
中文描述： 4 CHANNEL(S), 5M bps, SERIAL COMM CONTROLLER, PBGA64
封裝： 6 X 6 MM, 1.05 MM HEIGHT, PLASTIC, SOT-686-1, LFBGA-64
文件頁數： 15/52頁
文件大?。?/td> 647K
代理商： SC16C654BIEC
Philips Semiconductors
SC16C654/654D
Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 04 — 19 June 2003
15 of 52
9397 750 11617
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
suspend/resume transmissions. When double 8-bit Xon/Xoff characters are selected,
the SC16C654/654D compares two consecutive receive characters with two software
flow control 8-bit values (Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions
accordingly. Under the above described flow control mechanisms, flow control
characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed,
the SC16C654/654D automatically sends an Xoff message (when enabled) via the
serial TX output to the remote modem. The SC16C654/654D sends the Xoff1,2
characters as soon as received data passes the programmed trigger level. To clear
this condition, the SC16C654/654D will transmit the programmed Xon1,2 characters
as soon as receive data drops below the programmed trigger level.
6.8 Special feature software flow control
A special feature is provided to detect an 8-bit character when EFR[5] is set. When
8-bit character is detected, it will be placed on the user-accessible data stack along
with normal incoming RX data. This condition is selected in conjunction with
EFR[0-3]. Note that software flow control should be turned off when using this special
mode by setting EFR[0-3] to a logic 0.
The SC16C654/654D compares each incoming receive character with Xoff2 data. If a
match exists, the received data will be transferred to the FIFO, and ISR[4] will be set
to indicate detection of a special character. Although the Internal Register Table
(
Table 8
) shows each X-Register with eight bits of character information, the actual
number of bits is dependent on the programmed word length. Line Control Register
bits LCR[0-1] define the number of character bits, i.e., either 5 bits, 6 bits, 7 bits or
8 bits. The word length selected by LCR[0-1] also determine the number of bits that
will be used for the special character comparison. Bit 0 in the X-registers corresponds
with the LSB bit for the receive character.
6.9 Xon any feature
A special feature is provided to return the Xoff flow control to the inactive state
following its activation. In this mode, any RX character received will return the Xoff
flow control to the inactive state so that transmissions may be resumed with a remote
buffer. This feature is more fully defined in
Section 6.7 “Software flow control”
.
6.10 Hardware/software and time-out interrupts
Three special interrupts have been added to monitor the hardware and software flow
control. The interrupts are enabled by IER[5-7]. Care must be taken when handling
these interrupts. Following a reset, the transmitter interrupt is enabled, the
SC16C654/654D will issue an interrupt to indicate that the Transmit Holding Register
is empty. This interrupt must be serviced prior to continuing operations. The LSR
register provides the current singular highest priority interrupt only. It could be noted
that CTS and RTS interrupts have lowest interrupt priority. A condition can exist
where a higher priority interrupt may mask the lower priority CTS/RTS interrupt(s).
Only after servicing the higher pending interrupt will the lower priority CTS/TRS
interrupt(s) be reflected in the status register. Servicing the interrupt without
investigating further interrupt conditions can result in data errors.
相關PDF資料
PDF描述
SC16C654DIB64 Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
SC16C654IA68 Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
SC16C750 Universal Asynchronous Receiver/Transmitter (UART) with 64-byte FIFO
SC16C750IA44 Universal Asynchronous Receiver/Transmitter (UART) with 64-byte FIFO
SC16C750IB64 Universal Asynchronous Receiver/Transmitter (UART) with 64-byte FIFO
相關代理商/技術參數
參數描述
SC16C654BIEC,528 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654BIEC,551 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654BIEC,557 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654BIEC-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654BIEC-S 功能描述:UART 接口集成電路 4CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*