- 您現在的位置：買賣IC網 > PDF目錄372121 > SC16C650AIA44 (NXP SEMICONDUCTORS) Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder PDF資料下載
參數資料
| 型號： | SC16C650AIA44 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
| 中文描述： | 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PQCC44 |
| 封裝： | PLASTIC, MS-018, SOT-187-2, LCC-44 |
| 文件頁數： | 8/50頁 |
| 文件大?。?/td> | 642K |
| 代理商： | SC16C650AIA44 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Philips Semiconductors
SC16C650A
UART with 32-byte FIFO and IrDA encoder/decoder
Product data
Rev. 04 — 20 June 2003
8 of 50
9397 750 11622
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
IOR, IOR
24, 25
19, 20
21, 22
I
Read inputs.
When either IOR or IOR is active (LOW or HIGH,
respectively) while the UART is selected, the CPU is allowed to read
status information or data from a selected UART register. Only one of
these inputs is required for the transfer of data during a read operation;
the other input should be tied to its inactive level (i.e., IOR tied LOW or
IOR tied HIGH).
Ring indicator.
RI is a modem status signal. Its condition can be
checked by reading bit 6 (RI) of the modem status register. Bit 2 (
RI)
of the modem status register indicates that RI has transitioned from a
LOW to a HIGH level since the last read from the modem status
register. If the modem status interrupt is enabled when this transition
occurs, an interrupt is generated.
Request to send.
When active, RTS informs the modem or data set
that the UART is ready to receive data. RTS is set to the active level by
setting the RTS modem control register bit and is set to the inactive
(HIGH) level either as a result of a Master Reset or during loop mode
operations or by clearing bit 1 (RTS) of the MCR. In the auto-RTS
mode, RTS is set to the inactive level by the receiver threshold control
logic.
Receiver ready.
Receiver direct memory access (DMA) signaling is
available with RXRDY. When operating in the FIFO mode, one of two
types of DMA signaling can be selected using the FIFO control register
bit 3 (FCR[3]). When operating in the 16C450 mode, only DMA mode
0 is allowed. Mode 0 supports single-transfer DMA in which a transfer
is made between CPU bus cycles. Mode 1 supports multi-transfer
DMA in which multiple transfers are made continuously until the
receiver FIFO has been emptied. In DMA mode 0 (FCR0 = 0 or
FCR0 = 1, FCR3 = 0), when there is at least one character in the
receiver FIFO or receiver holding register, RXRDY is active (LOW).
When RXRDY has been active but there are no characters in the FIFO
or holding register, RXRDY goes inactive (HIGH). In DMA mode 1
(FCR0 = 1, FCR3 = 1), when the trigger level or the time-out has been
reached, RXRDY goes active (LOW); when it has been active but there
are no more characters in the FIFO or holding register, it goes inactive
(HIGH).
Serial data input.
RX is serial data input from a connected
communications device.
Serial data output.
TX is composite serial data output to a connected
communication device. TX is set to the marking (HIGH) level as a
result of Master Reset.
Transmitter ready.
Transmitter DMA signaling is available with
TXRDY. When operating in the FIFO mode, one of two types of DMA
signaling can be selected using FCR[3]. When operating in the
16C450 mode, only DMA mode 0 is allowed. Mode 0 supports
single-transfer DMA in which a transfer is made between CPU bus
cycles. Mode 1 supports multi-transfer DMA in which multiple transfers
are made continuously until the transmit FIFO has been filled.
2.5 V, 3 V or 5 V supply voltage.
Ground voltage.
RI
43
41
39
I
RTS
36
32
32
O
RXRDY
32
29
29
O
RX
11
7
10
I
TX
13
8
11
I
TXRDY
27
23
24
O
V
CC
V
SS
44
22
42
18
40
20
Power
Power
Table 2:
Symbol
Pin description
…continued
Pin
PLCC44 LQFP48 DIP40
Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C650AIB48 | Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C650AIN40 | Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C650BIA44 | 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder |
| SC16C650B | 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder |
| SC16C650BIN40 | 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C650AIA44,512 | 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650AIA44,518 | 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650AIA44,529 | 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650AIB48 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C650AIB48,128 | 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。