參數資料
型號： SC16C550BIA44
廠商： NXP Semiconductors N.V.
元件分類： 收發器
英文描述： 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
封裝： SC16C550BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html<1<week 51, 2004,;SC16C550BIA44<SOT187-2 (PLCC44)|<<http://www.nxp.com/packages/SOT187-2.html&l
文件頁數： 44/48頁
文件大?。?/td> 240K
代理商： SC16C550BIA44
SC16C550B_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 1 October 2008
44 of 48
NXP Semiconductors
SC16C550B
5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”
13. Soldering of through-hole mount packages
13.1 Introduction to soldering through-hole mount packages
This text gives a very brief insight into wave, dip and manual soldering.
Wave soldering is the preferred method for mounting of through-hole mount IC packages
on a printed-circuit board.
13.2 Soldering by dipping or by solder wave
Driven by legislation and environmental forces the worldwide use of lead-free solder
pastes is increasing. Typical dwell time of the leads in the wave ranges from
3 seconds to 4 seconds at 250
°
C or 265
°
C, depending on solder material applied, SnPb
or Pb-free respectively.
The total contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the plastic
body must not exceed the specified maximum storage temperature (T
stg(max)
). If the
printed-circuit board has been pre-heated, forced cooling may be necessary immediately
after soldering to keep the temperature within the permissible limit.
13.3 Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the
seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is
less than 300
°
C it may remain in contact for up to 10 seconds. If the bit temperature is
between 300
°
C and 400
°
C, contact may be up to 5 seconds.
MSL: Moisture Sensitivity Level
Fig 28. Temperature profiles for large and small components
001aac844
temperature
time
minimum peak temperature
= minimum soldering temperature
maximum peak temperature
= MSL limit, damage level
peak
temperature
相關PDF資料
PDF描述
SC16C550BIB48 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
SC16C550BIBS 5 V, 3.3 V and 2.5 V UART with 16-byte FIFOs
SC16C650BIB48 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C650BIBS 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder-decoder
SC16C652BIBS 5 V, 3.3 V and 2.5 V dual UART, 5 Mbit-s (max.) with 32-byte FIFOs and infrared (IrDA) encoder-decoder
相關代理商/技術參數
參數描述
SC16C550BIA44,512 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIA44,518 功能描述:UART 接口集成電路 1CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIA44,529 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C550BIA44512 制造商:NXP Semiconductors 功能描述:IC SINGLE UART FIFO 3MBPS 5.5V LCC44
SC16C550BIA44-S 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*