- 您現在的位置：買賣IC網 > PDF目錄372113 > SAA7118 (NXP Semiconductors N.V.) Multistandard video decoder with adaptive comb filter and component video input PDF資料下載
參數資料
| 型號： | SAA7118 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Multistandard video decoder with adaptive comb filter and component video input |
| 中文描述： | 多標準視頻解碼器與自適應梳狀濾波器和分量視頻輸入 |
| 文件頁數： | 81/169頁 |
| 文件大?。?/td> | 665K |
| 代理商： | SAA7118 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁
2001 May 30
81
Philips Semiconductors
Preliminary specification
Multistandard video decoder with adaptive
comb filter and component video input
SAA7118
10 BOUNDARY SCAN TEST
The SAA7118 has built-in logic and 5 dedicated pins to
support boundary scan testing which allows board testing
without special hardware (nails). The SAA7118 follows the
“IEEE Std. 1149.1 - Standard Test Access Port and
Boundary-Scan Architecture”set by the Joint Test Action
Group (JTAG) chaired by Philips.
The 5 special pins are Test Mode Select (TMS), Test
Clock (TCK), Test Reset (TRST), Test Data Input (TDI)
and Test Data Output (TDO).
The Boundary Scan Test (BST) functions BYPASS,
EXTEST, INTEST, SAMPLE, CLAMP and IDCODE are all
supported (see Table 34). Details about the JTAG
BST-TEST can be found in specification “IEEE Std.
1149.1” A file containing the detailed Boundary Scan
Description Language (BSDL) description of the SAA7118
is available on request.
Table 34
BST instructions supported by the SAA7118
10.1
Initialization of boundary scan circuit
The TAP (Test Access Port) controller of an IC should be
in the reset state (TEST_LOGIC_RESET) when the IC is
in functional mode. This reset state also forces the
instruction register into a functional instruction such as
IDCODE or BYPASS.
To solve the power-up reset, the standard specifies that
the TAP controller will be forced asynchronously to the
TEST_LOGIC_RESET state by setting the TRST pin
LOW.
10.2
Device identification codes
A device identification register is specified in “IEEE Std.
1149.1b-1994” It is a 32-bit register which contains fields
for the specification of the IC manufacturer, the IC part
number and the IC version number. Its biggest advantage
is the possibility to check for the correct ICs mounted after
production and determination of the version number of ICs
during field service.
When the IDCODE instruction is loaded into the BST
instruction register, the identification register will be
connected between TDI and TDO of the IC. The
identification register will load a component specific code
duringtheCAPTURE_DATA_REGISTERstateoftheTAP
controller and this code can subsequently be shifted out.
At board level this code can be used to verify component
manufacturer, type and version number. The device
identification register contains 32 bits, numbered 31 to 0,
where bit 31 is the most significant bit (nearest to TDI) and
bit 0 is the least significant bit (nearest to TDO);
see Fig.45.
INSTRUCTION
DESCRIPTION
BYPASS
This mandatory instruction provides a
minimum length serial path (1 bit)
between TDI and TDO when no test
operation of the component is
required.
This mandatory instruction allows
testing of off-chip circuitry and board
level interconnections.
This mandatory instruction can be
used to take a sample of the inputs
during normal operation of the
component. It can also be used to
preload data values into the latched
outputs of the boundary scan register.
This optional instruction is useful for
testing when not all ICs have BST.
This instruction addresses the bypass
register while the boundary scan
register is in external test mode.
EXTEST
SAMPLE
CLAMP
IDCODE
This optional instruction will provide
information on the components
manufacturer, part number and
version number.
This optional instruction allows testing
of the internal logic (no customer
support available).
This private instruction allows testing
by the manufacturer (no customer
support available).
INTEST
USER1
INSTRUCTION
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| SAA7118E | Multistandard video decoder with adaptive comb filter and component video input |
| SAA7118H | Multistandard video decoder with adaptive comb filter and component video input |
| SAA7120 | Digital Video Encoder (ConDENC) |
| SAA7120H-01 | Digital Video Encoder (ConDENC) |
| SAA7121 | Digital Video Encoder (ConDENC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA7118E | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multistandard video decoder with adaptive comb filter and component video input |
| SAA7118E/V1,518 | 功能描述:視頻 IC COMPONENT VID DECODER W/COMB F RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| SAA7118E/V1,551 | 功能描述:視頻 IC COMPONENT VID DECODER W/COMB F RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| SAA7118E/V1,557 | 功能描述:視頻 IC COMPONENT VID DECODER W/COMB F RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| SAA7118E/V1/M5 | 功能描述:視頻 IC COMPONENT + VIDEO PROCESSOR RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。