參數資料
型號: SAA7105H
廠商: NXP Semiconductors N.V.
元件分類: 通用總線功能
英文描述: Digital video encoder
文件頁數: 65/71頁
文件大?。?/td> 354K
代理商: SAA7105H
2004 Mar 04
65
Philips Semiconductors
Product specification
Digital video encoder
SAA7104H; SAA7105H
12.1
Reconstruction filter
Figure 17 shows a possible reconstruction filter for the
digital-to-analog converters. Due to its cut-off frequency of
6 MHz, it is not suitable for HDTV applications.
12.2
Analog output voltages
The analog output voltages are dependent on the total
load (typical value 37.5
), the digital gain parameters and
theI
2
C-bus settingsof the DACreference currents (analog
settings).
The digital output signals in front of the DACs under
nominal (nominal here stands for the settings given in
Tables 40 to 47 for example a standard PAL or NTSC
signal) conditions occupy different conversion ranges, as
indicated in Table 116 for a
100
100
colour bar signal.
By setting the reference currents of the DACs as shown in
Table 116, standard compliant amplitudes can be
achieved for all signal combinations; it is assumed that in
subaddress 16H, parameter DACF = 0000b, that means
the fine adjustment for all DACs in common is set to 0%.
If S-video output is desired, the adjustment for the C
(chrominance subcarrier) output should be identical to the
one for VBS (luminance plus sync) output.
Table 116
Digital output signals conversion range
SET/OUT
CVBS, SYNC TIP-TO-WHITE
VBS, SYNC TIP-TO-WHITE
RGB, BLACK-TO-WHITE
Digital settings
Digital output
Analog settings
Analog output
see Tables 40 to 47
1014
e.g. B DAC = 1FH
1.23 V (p-p)
see Tables 40 to 47
881
e.g. G DAC = 1BH
1.00 V (p-p)
see Table 35
876
e.g. R DAC = G DAC = B DAC = 0BH
0.70 V (p-p)
12.3
Suggestions for a board layout
Use separate ground planes for analog and digital ground.
Connect these planes only at one point directly under the
device, by using a 0
resistor directly at the supply stage.
Use separate supply lines for analog and digital supply.
Place the supply decoupling capacitors close to the supply
pins.
Use L
bead
(ferrite coil) in each digital supply line close to
the decoupling capacitors to minimize radiation energy
(EMC).
Place the analog coupling (clamp) capacitors close to the
analog input pins. Place the analog termination resistors
close to the coupling capacitors.
Be careful of hidden layout capacitors around the crystal
application.
Use serial resistors in clock, sync and data lines, to avoid
clock or data reflection effects and to soften data energy.
相關PDF資料
PDF描述
SAA7108 PC-CODEC
SAA7109 PC-CODEC
SAA7108E PC-CODEC
SAA7109E PC-CODEC
SAA7108AE HD-CODEC
相關代理商/技術參數
參數描述
SAA7105H/V1,518 功能描述:視頻 IC PC DENC WO MACROVISION LICENSE RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7105H/V1,557 功能描述:視頻 IC PC GRAPHICS 85MHZ RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7105HBG 功能描述:視頻 IC PC GRAPHICS 85MHZ ENCODER RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel
SAA7108 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:PC-CODEC
SAA7108AE 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:HD-CODEC