參數資料
型號： S71GL064A40BFI0B3
廠商： Spansion Inc.
英文描述： Stacked Multi-Chip Product (MCP) Flash Memory and RAM
中文描述： 堆疊式多芯片產品（MCP）的閃存和RAM
文件頁數： 43/102頁
文件大?。?/td> 1606K
代理商： S71GL064A40BFI0B3
March 31, 2005 S71GL032A_00_A0
S71GL032A Based MCPs
45
Advance
Informatio n
If DQ5 goes high during a program or erase operation, writing the reset command
returns the device to the read mode (or erase-suspend-read mode if the device
was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the sys-
tem must write the Write-to-Buffer-Abort Reset command sequence to reset the
device for the next operation.
Autoselect Command Sequence
The autoselect command sequence allows the host system to read several iden-
tifier codes at specific addresses:
Note: The device ID is read over three cycles. SA = Sector Address
The autoselect command sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle that contains the autoselect command. The
device then enters the autoselect mode. The system may read at any address any
number of times without initiating another autoselect command sequence:
The system must write the reset command to return to the read mode (or erase-
suspend-read mode if the device was previously in Erase Suspend).
Enter Secured Silicon Sector/Exit Secured Silicon
Sector Command Sequence
The Secured Silicon Sector region provides a secured data area containing an 8-
word random Electronic Serial Number (ESN). The system can access the Se-
cured Silicon Sector region by issuing the three-cycle Enter Secured Silicon
Sector command sequence. The device continues to access the Secured Silicon
Sector region until the system issues the four-cycle Exit Secured Silicon Sector
command sequence. The Exit Secured Silicon Sector command sequence returns
the device to normal operation. Table 22 shows the address and data require-
ments for both command sequences. See also “Secured Silicon Sector Flash
Memory Region” for further information. Note that the ACC function and unlock
bypass modes are not available when the Secured Silicon Sector is enabled.
Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is
initiated by writing two unlock write cycles, followed by the program set-up com-
mand. The program address and data are written next, which in turn initiate the
Embedded Program algorithm. The system is not required to provide further con-
trols or timings. The device automatically provides internally generated program
pulses and verifies the programmed cell margin. Table 22 shows the address and
data requirements for the word program command sequence, respectively.
Identifier Code
A7:A0
(x16)
A6:A-1
(x8)
Manufacturer ID
00h
Device ID, Cycle 1
01h
02h
Device ID, Cycle 2
0Eh
1Ch
Device ID, Cycle 3
0Fh
1Eh
Secured Silicon Sector Factory Protect
03h
06h
Sector Protect Verify
(SA)02h
(SA)04h
相關PDF資料
PDF描述
S71GL128NC0BAWAZ0 SPECIALTY MEMORY CIRCUIT, PBGA84
S71PL064JB0BFW0U0 SPECIALTY MEMORY CIRCUIT, PBGA56
S71PL129JC0BFW9Z2 Stacked Multi-Chip Product (MCP) Flash Memory
S71PL129NC0HFW4U3 SPECIALTY MEMORY CIRCUIT, PBGA64
S71PL191HB0BFI100 SPECIALTY MEMORY CIRCUIT, PBGA73
相關代理商/技術參數
參數描述
S71GL064A40BFI0F0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM
S71GL064A40BFI0F2 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM
S71GL064A40BFI0F3 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM
S71GL064A40BFW0B0 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM
S71GL064A40BFW0B2 制造商:SPANSION 制造商全稱:SPANSION 功能描述:Stacked Multi-Chip Product (MCP) Flash Memory and RAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*