- 您現在的位置：買賣IC網 > PDF目錄374664 > S3014 (Applied Micro Circuits Corp.) SONET/SDH Clock Recovery and Synthesis Unit(SONET/SDH時鐘恢復和合成器件) PDF資料下載
參數資料
| 型號： | S3014 |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | SONET/SDH Clock Recovery and Synthesis Unit(SONET/SDH時鐘恢復和合成器件) |
| 中文描述： | SONET / SDH的時鐘恢復和合成單元（SONET / SDH的時鐘恢復和合成器件） |
| 文件頁數： | 2/10頁 |
| 文件大小： | 99K |
| 代理商： | S3014 |
2
S3014
SONET/SDH CLOCK RECOVERY AND SYNTHESIS UNIT
S3014 OVERVIEW
Clock Recovery Mode
In the Clock Recovery mode, the S3014 supports
clock recovery for the STS-3/STM-1 and STS-12/
STM-4 rates. In this mode, ECL differential serial data is
input to the chip at the rate specified by the three SEL
pins, and clock recovery is performed on the incoming
data stream. An external ECL differential reference
clock (19.44, 51.84, or 155.52 MHz) is required to
minimize the PLL lock time and provide a stable output
clock source in the absence of serial input data.
Retimed data and clock are output from the S3014.
Clock Synthesis Mode
In the Clock Synthesis mode, the S3014 synthesizes up
to the STS-3/STM-1 and STS-12/STM-4 clock rates
from either a 19.44 MHz, 51.84 MHz, or 155.52 MHz
input reference frequency. STS-3/STM-1 jitter generation
is compliant with the SONET/SDH requirement for
0.01 U.I. (rms) maximum, given 14.1 ps (rms) jitter on
REFCLK in the 12 KHz to 1 MHz frequency band.
In this mode, a crystal oscillator is connected to the
ECL differential reference input and synthesized up to
the output frequency selected using the three SEL
pins. The Clock Synthesis mode is recognized by the
absence of data on the SERDATIP/N input pins. In
this mode, tie the SERDATIP pin to ground and tie the
SERDATIN pin to VTT (-2.0v) or to an ECL low level.
A programmable internal divider outputs a TTL clock
at the same frequency as the reference clock input via
the REFCKOUT output. The lock detect output will
remain consistently low in the Clock Synthesis mode.
CHARACTERISTICS
Performance
The S3014 PLL complies with the minimum jitter toler-
ance for clock recovery proposed for SONET/SDH
equipment defined by the T1X1.6/91-022 document,
when used with differential inputs and outputs as
shown in Figure 2.
Input Jitter Tolerance
Input jitter tolerance is defined as the peak to peak
amplitude of sinusoidal jitter applied on the input sig-
nal that causes an equivalent 1 dB optical/electrical
power penalty. SONET input jitter tolerance require-
ments are shown in Figure 2. The measurement
condition is the input jitter amplitude which causes an
equivalent of 1 dB power penalty.
Jitter Generation
Jitter generation is defined as the amount of jitter at
the OC-N/STS-N output of a SONET equipment.
Jitter generation shall not exceed 0.01 UI rms in OC-3
mode and 0.03 UI rms in OC-12 mode when measured
using a highpass filter with a 12 kHz cutoff frequency.
Serial Data Output Set-up and Hold Time
The output set-up and hold times are represented by
the waveforms shown in Figure 3.
Reference Clock Input
The required characteristics of the reference clock
are outlined below. Unless otherwise noted, specifi-
cations refer to both Clock Recovery and Clock
Synthesis modes of operation. While a single-ended
ECL reference clock may be used, additional jitter
due to edge movement related to threshold variations
from DC offsets may be induced.
Figure 2. Input Jitter Tolerance Specification
f0
f1
f2
f3
ft
0.15
1.5
15
Sinusoidal
Input Jitter
Amplitude
(UI p-p)
Frequency
OC/STS
Level
f0
(Hz)
f2
(Hz)
f3
(kHz)
ft
(kHz)
f1
(Hz)
3
12
10
10
30
30
300
300
6.5
25
75
250
Figure 3. Clock Output to Data Transition Delay
Output Frequency
155.52 MHz
622.08 MHz
SERDATOP/N Setup Time
2.5 ns
450 ps
SERDATOP/N Hold Time
2.5 ns
650 ps
tsu
th
SERCLKOP/N
SERDATOP/N
相關PDF資料 |
PDF描述 |
|---|---|
| S3015 | SONET/SDH Clock Recovery and Synthesis Unit(SONET/SDH時鐘恢復和合成單元) |
| S3019 | SONET/SDH/ATM OC-3/12 Transceiver W/CDR(SONET/SDH/ATM收發器(完全集成OC-3/12接口器件)) |
| S3023 | SONET/SDH/ATM Clock Recovery Unit(SONET/SDH/ATM時鐘恢復單元) |
| S3024 | SONET/SDH/ATM Clock Recovery Unit(帶片上鎖相環的SONET/SDH/ATM時鐘恢復單元) |
| S3025 | SONET/SDH/ATM Clock Recovery Unit(帶片上高頻鎖相環的SONET/SDH/ATM時鐘恢復單元) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S3014-2 | 制造商:Alpha 3 Manufacturing 功能描述: |
| S3015 | 制造商:UNBRANDED 功能描述:FIRST AID BADGE |
| S-30151-01 | 功能描述:環形MIL規格工具、五金與附件 RoHS:否 制造商:Amphenol Industrial MIL 類型:MIL-DTL-5015 系列:97 產品類型:Dummy Receptacles 用于:97 Series Plugs |
| S3015180 | 制造商:ROEBUCK 功能描述:RBK ABRSVE FLAP WHL 30MMDIAX15MM 180 GRD |
| S3015A | 制造商:amcc 功能描述:3015 |
發布緊急采購，3分鐘左右您將得到回復。