參數資料
型號： S29GL128N90TFIV23
廠商： SPANSION LLC
元件分類： PROM
英文描述： 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
中文描述： 8M X 16 FLASH 3V PROM, 90 ns, PDSO56
封裝： MO-142BEC, LEAD FREE, TSOP-56
文件頁數： 57/100頁
文件大?。?/td> 952K
代理商： S29GL128N90TFIV23
S29GL-N_00_B3 October 13, 2006
S29GL-N MirrorBit Flash Family
55
D a t a S h e e t
Figure 2. Program Operation
Program Suspend/ Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or
a Write to Buffer programming operation so that data can be read from any non-suspended
sector. When the Program Suspend command is written during a programming process, the
device halts the program operation within 15 μs maximum (5
μs typical) and updates the sta-
tus bits. Addresses are not required when writing the Program Suspend command.
After the programming operation is suspended, the system can read array data from any
non-suspended sector. The Program Suspend command may also be issued during a pro-
gramming operation while an erase is suspended. In this case, data may be read from any
addresses not in Erase Suspend or Program Suspend. If a read is needed from the Secured
Silicon Sector area (One-time Program area), then user must use the proper command se-
quences to enter and exit this region.
Note that the Secured Silicon Sector autoselect, and
CFI functions are unavailable when program operation is in progress.
The system may also write the autoselect command sequence when the device is in the Pro-
gram Suspend mode. The system can read as many autoselect codes as required. When the
device exits the autoselect mode, the device reverts to the Program Suspend mode, and is
ready for another valid operation. See
Autoselect Command Sequence on page 51
for more
information.
After the Program Resume command is written, the device reverts to programming. The sys-
tem can determine the status of the program operation using the DQ7 or DQ6 status bits, just
START
Write Program
Command Sequence
Data Poll
from System
Verify Data
No
Yes
Last Address
No
Yes
Programming
Completed
Increment Address
Embedded
Program
algorithm
in progress
Note:
See
Table 12 on page 63
and
Table 14 on
page 65
for program command sequence.
相關PDF資料
PDF描述
S29GL256N10FAI012 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL256N10FAI022 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL256N10FAIV12 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL256N10FAIV22 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
S29GL256N10FFI012 3.0 Volt-only Page Mode Flash Memory featuring 110 nm MirrorBit⑩ Process Technology
相關代理商/技術參數
參數描述
S29GL128P10FAI010 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 16MX8/8MX16 100NS 64BGA - Trays 制造商:Spansion 功能描述:SPZS29GL128P10FAI010 IC 128M PAGE-MODE F
S29GL128P10FAI020 制造商:Spansion 功能描述: 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 16MX8/8MX16 100NS 64BGA - Trays 制造商:Spansion 功能描述:SPZS29GL128P10FAI020 IC 128M FLASH BGA
S29GL128P10FAI022 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 128MBIT 16MX8/8MX16 100NS 64BGA - Tape and Reel
S29GL128P10FAIR20 制造商:Spansion 功能描述:
S29GL128P10FFI010 功能描述:閃存 128Mb 3V 110ns Parallel NOR 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*