- 您現在的位置：買賣IC網 > PDF目錄374647 > S2104 (Applied Micro Circuits Corp.) Quad Fibre Channel Device(帶鎖相環時鐘合成器的光纖通道四收發器) PDF資料下載
參數資料
| 型號： | S2104 |
| 廠商： | Applied Micro Circuits Corp. |
| 英文描述： | Quad Fibre Channel Device(帶鎖相環時鐘合成器的光纖通道四收發器) |
| 中文描述： | 四光纖通道設備（帶鎖相環時鐘合成器的光纖通道四收發器） |
| 文件頁數： | 11/33頁 |
| 文件大?。?/td> | 342K |
| 代理商： | S2104 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
11
S2104
QUAD FIBRE CHANNEL DEVICE
October 6, 2000 / Revision E
Figure 9. S2104 Diagnostic Loopback Operation
CRU
CSU
OTHER OPERATING MODES
Operating Frequency Rate
The S2104 is designed to operate at the Fibre Chan-
nel rate of 1.062 GHz.
Loopback Mode
When loopback mode is enabled, the serial data
from the transmitter is provided to the serial input of
the receiver, as shown in Figure 9. This provides the
ability to perform system diagnostics and off-line
testing of the interface to verify the integrity of the
serial channel. Loopback mode is enabled indepen-
dently for each channel using its respective
loopback-enable input, LPEN.
TEST MODES
The RESET pin is used to initialize the Transmit
FIFOs and must be asserted (LOW) prior to entering
the normal operational state (see section Transmit
FIFO Initialization).
Note: Serial output data remains active during loopback opera-
tion to enable other system tests to be performed.
JTAG TESTING
The JTAG implementation for the S2104 is compli-
ant with the IEEE1149.1 requirements. JTAG is used
to test the connectivity of the pins on the chip. The
TAP, (Test Access Port), provides access to the test
logic of the chip. When TRST is asserted the TAP is
initialized. TAP is a state machine that is controlled
by TMS. The test instruction and data are loaded
through TDI on the rising edge of TCK. When TMS is
high the test instruction is loaded into the instruction
register. When TMS is low the test data is loaded
into the data register. TDO changes on the falling
edge of TCK. All input pins, including clocks, that
have boundary scan are observe only. They can be
sampled in either normal operational or test mode.
All output pins that have boundary scan, are observe
and control. They can be sampled as they are driven
out of the chip in normal operational mode, and they
can be driven out of the chip in test mode using the
Extest instruction. Since JTAG testing operates only
on digital signals there are some pins with analog
signals that JTAG does not cover. The JTAG imple-
mentation has the three required instruction, Bypass,
Extest, and Sample/Preload.
Instruction
BYPASS
EXTEST
SAMPLE/PRELOAD
ID CODE
Code
11
00
01
10
JTAG Instruction Description:
The BYPASS register contains a single shift-register
stage and is used to provide a minimum-length serial
path between the TDI and TDO pins of a component
when no test operation of that component is re-
quired. This allows more rapid movement of test
data to and from other components on a board that
are required to perform test operations.
The EXTEST instruction allows testing of off-chip cir-
cuitry and board level interconnections. Data would
typically be loaded onto the latched parallel outputs
of boundary-scan shift-register stages using the
SAMPLE/PRELOAD instruction prior to selection of
the EXTEST instruction.
The SAMPLE/PRELOAD instruction allows a snap-
shot of the normal operation of the component to be
taken and examined. It also allows data values to be
loaded onto the latched parallel outputs of the
boundary-scan shift register prior to selection of the
other boundary-scan test instructions.
相關PDF資料 |
PDF描述 |
|---|---|
| S212S01 | SIP Type SSR for Medium Power Control |
| S212S02 | SIP Type SSR for Medium Power Control |
| S216S01 | SIP Type SSR for Medium Power Control |
| S216S02 | IT(rms)÷16A, Zero Cross type SIP 4pin Triac output SSR |
| S216S02F | IT(rms)÷16A, Zero Cross type SIP 4pin Triac output SSR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-210-48 | 功能描述:線性和開關式電源 211.2W 48V 4.4A RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
| S-210-5 | 功能描述:線性和開關式電源 200W 5V 40A RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
| S2105QA | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:21/32/43/60 VOICE ROM |
| S2105QE | 制造商:MOSEL 制造商全稱:MOSEL 功能描述:21/32/43/60 VOICE ROM |
| S2107 | 制造商:LAPP/CONTACT CONNECTORS 功能描述:Connector, Strain Relief, Liquid Tight, Non Metallic, PG-7 Thread |
發布緊急采購，3分鐘左右您將得到回復。