參數資料
型號： S-7750C71XX-HCT1
元件分類： 微控制器/微處理器
英文描述： SPECIALTY MICROPROCESSOR CIRCUIT, PBGA16
封裝： 1.93 X 2.07 MM, 0.6 MM HEIGHT, LEAD FREE, WLP-16
文件頁數： 18/44頁
文件大?。?/td> 563K
代理商： S-7750C71XX-HCT1
PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT)
Rev.2.0_00
S-7750C
Seiko Instruments Inc.
25
How to Use S-7750C
1. SDA I/O pin and SCL input pin
In consideration of I
2C-bus protocol function, the SDA I/O and SCL input pins*1 should be connected with a pull-up
resister of approx.1 to 5 k
Ω.
The S-7750C cannot transmit normally without using a pull-up resistor.
*1.
In the case that the SCL input pin of the S-7750C is connected to the tri-state output pin in the master device,
connect the SCL input pin with a pull-up resistor as well in order not to set the SCL input pin in high impedance.
This prevents the S-7750C from error caused by high impedance from the tri-state pin when resetting the master
device during the voltage drop.
2. Reset after transmission interruption
The S-7750C does not have a pin to reset, but it generally resets the internal circuit by inputting a stop or start
condition. However, in case that transmission is interrupted, for example, only the master device is reset because the
power supply voltage drops during transmission; the internal circuit maintains the status before interruption. If the
status is that the SDA pin outputs “L” (outputs an acknowledge signal or in Read), the S-7750C does not perform the
next operation because it cannot receive a start or stop condition from the master device. Therefore it is necessary to
finish outputting an acknowledgment signal and the Read operation in SDA. Figure 31 shows how to reset.
First, input a start condition. (While the SDA pin is outputting “L”, the S-7750C does not go in the start condition but
this “L” output does not affect on the slave device.) Next, input clock (27 clocks) which is equivalent to 3-byte data
access from the SCL pin. During this procedure, pull up the SDA line which is connected closer to the master device.
Due to this, the SDA pin’s I/O prior to transmission interruption ends so that the SDA pin goes in “H”. After that, by
inputting a stop condition, the S-7750C returns to the status possible to perform the general transmission. It is
recommended to perform this reset when you initialize, after power-on the master device. A circuit for prevention
malfunction by a low power supply voltage is equipped in the S-7750C, thus it automatically resets internally when a
low voltage is applied to the S-7750C.
1
2
26
27
8
9
Start
Condition
Stop
Condition
Clock equivalent to 3-byte data access
SCL
SDA
Master
SDA
Slave
“L” or
“High-Z”
“L” or
“High-Z”
“L” or
“High-Z”
Figure 31 How to Reset S-7750C
相關PDF資料
PDF描述
S-940-L55 3.18 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH LOGIC OUTPUT
S-940-W55 3.18 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH LOGIC OUTPUT
S153P PIN PHOTO DIODE
S16MD01 TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX
S16MD02 TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX
相關代理商/技術參數
參數描述
S-7750C72XX-HCT1 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT)
S-7750C73XX-HCT1 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT)
S-7760A 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT)
S-7760A00XX-HCT1 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT)
S-7760A00XX-TCT1G 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:PROGRAMMABLE PORT CONTROLLER (PORT EXPANDER WITH BUILT-IN E2PROM CIRCUIT)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*