參數資料
型號: RMPA2451-TB
廠商: Fairchild Semiconductor Corporation
英文描述: 2.4?2.5 GHz GaAs MMIC Power Amplifier
中文描述: 2.4?2.5千兆赫的GaAs MMIC功率放大器
文件頁數: 4/7頁
文件大小: 489K
代理商: RMPA2451-TB
2004 Fairchild Semiconductor Corporation
RMPA2451 Rev. B
R
Figure 2. Functional Block Diagram
GROUND
(Back of the Chip)
MMIC CHIP
Pins #4, #6, #7, #9, #12
Ground
Pin #5
Vd1
Pins #1, #2, #3
RF OUTPUT & Vd2
Pin #10
Vg1
Pin #11
Vg2
Pin #8
RF INPUT
Test Procedure for the Evaluation Board (RMPA2451-TB)
It is important that the following points be noted prior to
testing; Pin designations are as shown in Figure 2 and 4.
V
gg1
and V
gg2
are the negative Gate bias voltages
applied at the pins of the evaluation test board.
V
dd1
and V
dd2
are the positive Drain bias voltages
applied at the pins of the evaluation test board.
V
g1
and V
g2
are the negative Gate bias voltages applied
at the pins of the package.
V
d1
and V
d2
are the positive Drain bias voltages applied
at the pins of the package.
CAUTION: LOSS OF GATE VOLTAGES (VG1, VG2)
WHILE DRAIN VOLTAGES (VD1, VD2) ARE PRESENT
MAY DAMAGE THE AMPLIFIER.
The following sequence of procedures must be followed to
properly test the amplifier:
Step 1:
Turn the RF power OFF.
Step 2:
the ground of the DC supplies.
Use the GND terminals of the evaluation board for
Step 3:
both V
Apply a nominal voltage of approximately - 3.0V to
and V
gg2
terminals.
gg1
Step 4:
terminals. Adjust V
Drain current, I
stage quiescent Drain current, I
Apply a nominal voltage of +5.0V to the V
to provide a second stage quiescent
, of 340 mA. Adjust V
dd
gg2
dd2
gg1
to give a first
d1
of 60mA.
Step 5:
(2.4 - 2.5 GHz) at an initial input power level of -10 dBm.
Apply an RF signal within the ISM frequency range
Step 6:
ments, a second RF signal generator with a frequency
difference of 1 MHz is required, along with an appropriate
power combiner. The test configuration should allow this
additional generator to provide the same input power level
as the first generator into the device. Intermodulation
readings may then be made at the required total output
power levels.
To perform intermodulation product measure-
Step 7:
increase the magnitudes of V
alternatively to operate at higher quiescent Drain currents,
the magnitudes of V
gg1
and V
accordingly.
To operate at lower quiescent Drain currents,
gg1
and V
gg2
as required,
gg2
should be decreased
Step 8:
sequence should be reversed.
When turning the amplifier OFF, the power-up
相關PDF資料
PDF描述
RMPA2453 2.4?2.5 GHz InGaP HBT Linear Power Amplifier
RMPA2455 2.4-2.5 GHz 1 Watt InGaP HBT Linear Power Amplifier
RMPA2456 2.4-2.5 GHz InGaP HBT Low Current Linear Power Amplifier
RMPA2458 2.4-2.5 GHz InGaP HBT Low Current Linear Power Amplifier
RMPA2550 2.4-2.5 GHz and 5.15-5.85 GHz Dual Band InGaP HBT Linear Power Amplifier
相關代理商/技術參數
參數描述
RMPA2453 功能描述:射頻放大器 2.4-2.5 GHz InGaP HBT Linear Power Amp RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
RMPA2455 功能描述:射頻放大器 2.4-2.5 GHz 1 Watt InGaP HBT RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
RMPA2456 制造商:Fairchild Semiconductor Corporation 功能描述:
RMPA2458 功能描述:射頻放大器 2.4-2.5 GHZ INGAP HBT LINEAR P RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel
RMPA2458_059 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:2.4-2.5 GHz InGaP HBT Low Current Linear Power Amplifier