- 您現在的位置：買賣IC網 > PDF目錄69306 > R5F212BASNFA 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | R5F212BASNFA |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| 封裝： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-48 |
| 文件頁數： | 20/138頁 |
| 文件大?。?/td> | 492K |
| 代理商： | R5F212BASNFA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁
203
4317K–AVR–03/2013
AT90PWM2/3/2B/3B
(TXBn = 0) is being transmitted. The slave MCUs must in this case be set to use a 9-bit charac-
ter frame format.
The following procedure should be used to exchange data in Multi-processor Communication
mode:
1.
All Slave MCUs are in Multi-processor Communication mode (MPCM in
UCSRA is set).
2.
The Master MCU sends an address frame, and all slaves receive and read this frame. In
the Slave MCUs, the RXC flag in UCSRA will be set as normal.
3.
Each Slave MCU reads the UDR Register and determines if it has been selected. If so, it
clears the MPCM bit in UCSRA, otherwise it waits for the next address byte and keeps
the MPCM setting.
4.
The addressed MCU will receive all data frames until a new address frame is received.
The other Slave MCUs, which still have the MPCM bit set, will ignore the data frames.
5.
When the last data frame is received by the addressed MCU, the addressed MCU sets
the MPCM bit and waits for a new address frame from master. The process then repeats
from 2.
Using any of the 5- to 8-bit character frame formats is possible, but impractical since the
Receiver must change between using N and N+1 character frame formats. This makes full-
duplex operation difficult since the Transmitter and Receiver use the same character size set-
ting. If 5- to 8-bit character frames are used, the Transmitter must be set to use two stop bit
(USBS = 1) since the first stop bit is used for indicating the frame type.
18.10 USART Register Description
18.10.1
USART I/O Data Register – UDR
Bit 7:0 – RxB7:0: Receive Data Buffer (read access)
Bit 7:0 – TxB7:0: Transmit Data Buffer (write access)
The USART Transmit Data Buffer Register and USART Receive Data Buffer Registers share the
same I/O address referred to as USART Data Register or UDR. The Transmit Data Buffer Reg-
ister (TXBn) will be the destination for data written to the UDR Register location. Reading the
UDR Register location will return the contents of the Receive Data Buffer Register (RXBn).
For 5-, 6-, or 7-bit characters the upper unused bits will be ignored by the Transmitter and set to
zero by the Receiver.
The transmit buffer can only be written when the UDRE flag in the UCSRA Register is set. Data
written to UDR when the UDRE flag is not set, will be ignored by the USART Transmitter. When
data is written to the transmit buffer, and the Transmitter is enabled, the Transmitter will load the
data into the Transmit Shift Register when the Shift Register is empty. Then the data will be seri-
ally transmitted on the TxDn pin.
The receive buffer consists of a two level FIFO. The FIFO will change its state whenever the
receive buffer is accessed.
This register is available in both USART and EUSART modes.
Bit
765
43
21
0
RXB[7:0]
UDR (Read)
TXB[7:0]
UDR (Write)
Read/Write
R/W
Initial Value
000
00
0
相關PDF資料 |
PDF描述 |
|---|---|
| R5F212ACSDFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BCSNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BASNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212ACSNFP | 16-BIT, FLASH, 20 MHz, RISC MICROCONTROLLER, PQFP48 |
| R5F212BASNLG | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PBGA64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| R5F212BASNFA#U0 | 制造商:Renesas Electronics Corporation 功能描述:IC MCU 16BIT 96KB FLASH 64LQFP 制造商:Renesas Electronics Corporation 功能描述:R8C Series 16 bit 7 kB RAM 96 kB Flash Single Chip Microcontroller SMT -LQFP-64 |
| R5F212BASNFA#V0 | 功能描述:IC MCU 16/32BIT 96KB FLSH 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/2B 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| R5F212BASNFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:RENESAS MCU |
| R5F212BASNFP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 16-Bit R8C CISC 96KB Flash 2.5V/3.3V/5V 64-Pin LQFP 制造商:Renesas Electronics Corporation 功能描述:MCU 16BIT R8C CISC 96KB FLASH 2.5V/3.3V/5V 64LQFP - Trays 制造商:Renesas Electronics Corporation 功能描述:MCU R8C/2B 制造商:Renesas Electronics 功能描述:MCU 16-Bit R8C CISC 96KB Flash 2.5V/3.3V/5V 64-Pin LQFP 制造商:Renesas 功能描述:MCU 16-Bit R8C CISC 96KB Flash 2.5V/3.3V/5V 64-Pin LQFP |
| R5F212BASNFP#V0 | 功能描述:IC R8C/2B MCU FLASH 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:R8C/2x/2B 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323 |
發布緊急采購，3分鐘左右您將得到回復。