參數資料
型號： QL6250E-8PS484C
廠商： QUICKLOGIC CORP
元件分類： FPGA
英文描述： FPGA, 960 CLBS, 248160 GATES, PBGA484
封裝： 23 X 23 MM, 1 MM PITCH, MS-034AAJ-1, PLASTIC, BGA-484
文件頁數： 40/64頁
文件大?。?/td> 850K
代理商： QL6250E-8PS484C
2006 QuickLogic Corporation
Eclipse-E Family Data Sheet Rev. A
45
The rest of the PQ208 pins should be terminated at the board level in the manner presented in Table 28.
The rest of the PT280 and PS484 pins should be terminated at the board level in the manner presented in
Table 28: PQ208 Recommended Unused Pin Terminations
Signal Name
Recommended Termination
PLLOUT<x>a
a. x represents a number.
In earlier versions, the recommendation for unused PLLOUT pins was that they be connected to
VCC or GND. This was acceptable for Rev. D (and earlier) silicon, including all 0.25 m devices.
For Rev. G (and later) silicon, unused PLLOUT pins should be left unconnected. Used PLLOUT
pins will normally be connected to inputs, but can also be left unconnected. For the truth table of
PLLOUT connections, refer to
IOCTRL<y>b
b. y represents an alphabetical character.
There is an internal pulldown resistor to GND on this pin. This pin should be tied to GND if it is
not used. For backwards compatibility with Eclipse, it can be tied to VDED or GND. If tied to
VDED, it will draw no more than 20 A per IOCTRL pin due to the pulldown resistor.
CLK/PLLIN<x>
Any unused clock pins should be connected to VDED or GND.
PLLRST<x>
If a PLL module is not used, then the associated PLLRST<x> must be connected to VDED.
INREF<y>
If an I/O bank does not require the use of the INREF signal the pin should be connected to GND.
Table 29: PT280 and PS484 Recommended Unused Pin Terminations
Signal Name
Recommended Termination
PLLOUT<x>a
a. x represents a number.
In earlier versions, the recommendation for unused PLLOUT pins was that they be connected to
VCC or GND. This was acceptable for Rev. D (and earlier) silicon, including all 0.25 m devices.
For Rev. G (and later) silicon, unused PLLOUT pins should be left unconnected. Used PLLOUT
pins will normally be connected to inputs, but can also be left unconnected. For the truth table of
PLLOUT connections, refer to
IOCTRL<y>b
b. y represents an alphabetical character.
There is an internal pulldown resistor to GND on this pin. This pin should be tied to GND if it is
not used. For backwards compatibility with Eclipse, it can be tied to VCCIO(C) or GND. If tied to
VCCIO(C), it will draw no more than 20 A per IOCTRL pin due to the pulldown resistor.
CLK/PLLIN<x>
Any unused clock pins should be connected to VCCIO(C) or GND.
PLLRST<x>
If a PLL module is not used, then the associated PLLRST<x> must be connected to VCCIO(C).
INREF<y>
If an I/O bank does not require the use of the INREF signal the pin should be connected to GND.
Table 30: Recommended PLLOUT Terminations Truth Table
PLL_RESET
Recommend PLLOUT Termination
0
Must be left unconnected.
1
May be left unconnected, or connected to GND. Must not be connected to VCC.
相關PDF資料
PDF描述
QL6250E-8PS484I FPGA, 960 CLBS, 248160 GATES, PBGA484
QL6250E-8PS484M FPGA, 960 CLBS, 248160 GATES, PBGA484
QL6325-4PB516C FPGA, 1536 CLBS, 320640 GATES, PBGA516
QL8150-6PTN196M FPGA, 640 CLBS, 188946 GATES, PBGA196
QL8150-8PTN196C FPGA, 640 CLBS, 188946 GATES, PBGA196
相關代理商/技術參數
參數描述
QL6325PQ208 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ASIC
QL6325PT280 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ASIC
QL63D5SA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:InGaAlP Laser Diode
QL63F5SA 制造商:未知廠家 制造商全稱:未知廠家 功能描述:InGaAlP Laser Diode
QL63H5S-A 制造商:ROITHNER 制造商全稱:ROITHNER 功能描述:INGaAIP Laser Diode
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*