參數資料
型號： PM6686
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： SWITCHING CONTROLLER, QCC32
封裝： 5 X 5 MM, 1 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-32
文件頁數： 40/50頁
文件大?。?/td> 1066K
代理商： PM6686
PM6686
PCB design guidelines
Doc ID 15281 Rev 4
45/50
12
PCB design guidelines
The layout is very important in terms of efficiency, stability and noise of the system. It is
possible to refer to the PM6686 demonstration board for a complete layout example.
For good PC board layout follows these guidelines:
●
Place on the top side all the power components (inductors, input and output capacitors,
MOSFETs and diodes). Refer them to a power ground plan, PGND. If possible, reserve
a layer to PGND plan. The PGND plan is the same for both the switching sections.
●
AC current paths layout is very critical (see Figure 58). The first priority is to minimize
their length. Trace the LS MOSFET connection to PGND plan as short as possible.
Place the synchronous diode D near the LS MOSFET. Connect the LS MOSFET drain
to the switching node with a short trace.
●
Place input capacitors near HS MOSFET drain. It is recommended to use the same
input voltage plan for both the switching sections, in order to put together all input
capacitors.
●
Place all the sensitive analog signals (feedbacks, voltage references, current sense
paths) on the bottom side of the board or in an inner layer. Isolate them from the power
top side with a signal ground layer, SGND. Connect the SGND and PGND plans only in
one point (a multiple vias connection is preferable to a 0
Ω resistor connection) near the
PGND device pin. Place the device on the top or on the bottom size and connect the
exposed pad and the SGND pins to the SGND plan (see Figure 58).
●
As general rule, make the high-side and low-side drivers traces wide and short.
●
The high-side driver is powered by the bootstrap circuit. It’s very important to place
capacitor CBOOT as near as possible to the BOOT pin (for example on the layer
opposite to the device). Route HGATE and PHASE traces as near as possible in order
to minimize the area between them.
●
The low-side gate driver is powered by PVCC pin. Placing PGND and LGATE pins near
the low-side MOSFETs reduces the length of the traces and the crosstalk noise
between the two sections.
●
The linear regulator outputs are referred to SGND as long as the reference voltages
VREF2 and VREF3. Place their output filtering capacitors as near as possible to the
device.
●
Place input filtering capacitors near PVCC, VCC and VIN pins.
相關PDF資料
PDF描述
PM75B6L1C060 AC MOTOR CONTROLLER, DMA19
PMB2304T PLL FREQUENCY SYNTHESIZER, 220 MHz, PDSO14
PMB2306R PLL FREQUENCY SYNTHESIZER, 120 MHz, PDSO16
PMB2306T PLL FREQUENCY SYNTHESIZER, 120 MHz, PDSO14
PMB2347 PLL FREQUENCY SYNTHESIZER, 2800 MHz, PDSO20
相關代理商/技術參數
參數描述
PM6686TR 功能描述:DC/DC 開關控制器 Step-down Controller w/adj. voltages-dual RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
PM6-6F-L 功能描述:端子 Metric Fork Terminal non-insulated, 4.0 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
PM6-6R-D 制造商:Panduit Corp 功能描述:
PM6-6R-L 功能描述:端子 Metric Ring Terminal non-insulated, 2.5 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
PM6-6R-X 功能描述:端子 Metric Ring Terminal non-insulated, 2.5 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*