- 您現在的位置：買賣IC網 > PDF目錄98055 > PM6686 (STMICROELECTRONICS) SWITCHING CONTROLLER, QCC32 PDF資料下載
參數資料
| 型號： | PM6686 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, QCC32 |
| 封裝： | 5 X 5 MM, 1 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, VFQFPN-32 |
| 文件頁數： | 32/50頁 |
| 文件大?。?/td> | 1066K |
| 代理商： | PM6686 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
Application information
PM6686
38/50
Doc ID 15281 Rev 4
10
Application information
10.1
External components selection
10.1.1
Inductor
Once that switching frequency is defined, inductor selection depends on the desired
inductor ripple current and load transient performance.
Low inductance means great ripple current and could generate great output noise. On the
other hand, low inductor values involve fast load transient response.
A good compromise between the transient response time, the efficiency, the cost and the
size is to choose the inductor value in order to maintain the inductor ripple current
ΔI
L
between 20% and 50% of the maximum output current ILOAD (max). The maximum
ΔI
L
occurs at the maximum input voltage. With these considerations, the inductor value can be
calculated with the following relationship:
Equation 8
Where fSW is the switching frequency, VIN is the input voltage, VOUT is the output voltage
and
ΔI
L is the selected inductor ripple current.
In order to prevent overtemperature working conditions, inductor must be able to provide an
RMS current greater than the maximum RMS inductor current ILRMS:
Equation 9
Where
ΔI
L(max) is the maximum ripple current:
Equation 10
If hard saturation inductors are used, the inductor saturation current should be much greater
than the maximum inductor peak current Ipeak:
Equation 11
Using soft-saturation inductors it’s possible to choose inductors with saturation current limit
nearly to Ipeak.
Below there is a list of some inductor manufacturers.
IN
OUT
L
sw
OUT
IN
V
I
f
V
L
×
Δ
×
=
12
(max))
I
(
(max))
I
(
I
2
L
2
LOAD
LRMS
Δ
+
=
max
IN
OUT
sw
OUT
max
IN
L
V
L
f
V
(max)
I
×
=
Δ
2
(max)
I
(max)
I
Ipeak
L
LOAD
Δ
+
=
相關PDF資料 |
PDF描述 |
|---|---|
| PM75B6L1C060 | AC MOTOR CONTROLLER, DMA19 |
| PMB2304T | PLL FREQUENCY SYNTHESIZER, 220 MHz, PDSO14 |
| PMB2306R | PLL FREQUENCY SYNTHESIZER, 120 MHz, PDSO16 |
| PMB2306T | PLL FREQUENCY SYNTHESIZER, 120 MHz, PDSO14 |
| PMB2347 | PLL FREQUENCY SYNTHESIZER, 2800 MHz, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PM6686TR | 功能描述:DC/DC 開關控制器 Step-down Controller w/adj. voltages-dual RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| PM6-6F-L | 功能描述:端子 Metric Fork Terminal non-insulated, 4.0 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
| PM6-6R-D | 制造商:Panduit Corp 功能描述: |
| PM6-6R-L | 功能描述:端子 Metric Ring Terminal non-insulated, 2.5 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
| PM6-6R-X | 功能描述:端子 Metric Ring Terminal non-insulated, 2.5 RoHS:否 制造商:AVX 產品:Junction Box - Wire to Wire 系列:9826 線規:26-18 接線柱/接頭大小: 絕緣: 顏色:Red 型式:Female 觸點電鍍:Tin over Nickel 觸點材料:Beryllium Copper, Phosphor Bronze 端接類型:Crimp |
發布緊急采購，3分鐘左右您將得到回復。