- 您現在的位置：買賣IC網 > PDF目錄368024 > PIC16C62B (Microchip Technology Inc.) 28-Pin 8-Bit CMOS Microcontrollers(28引腳，8位CMOS微控制器) PDF資料下載
參數資料
| 型號： | PIC16C62B |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 28-Pin 8-Bit CMOS Microcontrollers(28引腳，8位CMOS微控制器) |
| 中文描述： | 28引腳8位CMOS微控制器（28引腳，8位的CMOS微控制器） |
| 文件頁數： | 41/120頁 |
| 文件大?。?/td> | 2122K |
| 代理商： | PIC16C62B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
PIC16C62B/72A
1999 Microchip Technology Inc.
Preliminary
DS35008B-page 41
8.3
SSP I
2
C Operation
The SSP module in I
2
C mode fully implements all slave
functions, except general call support, and provides
interrupts on start and stop bits in hardware to support
firmware implementations of the master functions. The
SSP module implements the standard mode specifica-
tions, as well as 7-bit and 10-bit addressing.
Two pins are used for data transfer. These are the
RC3/SCK/SCL pin, which is the clock (SCL), and the
RC4/SDI/SDA pin, which is the data (SDA). The user
must configure these pins as inputs or outputs through
the TRISC<4:3> bits.
The SSP module functions are enabled by setting SSP
Enable bit SSPEN (SSPCON<5>).
FIGURE 8-2:
SSP BLOCK DIAGRAM
(I
2
C MODE)
The SSP module has five registers for I
2
C operation.
These are the:
SSP Control Register (SSPCON)
SSP Status Register (SSPSTAT)
Serial Receive/Transmit Buffer (SSPBUF)
SSP Shift Register (SSPSR) - Not accessible
SSP Address Register (SSPADD)
The SSPCON register allows control of the I
2
C opera-
tion. Four mode selection bits (SSPCON<3:0>) allow
one of the following I
2
C modes to be selected:
I
2
C Slave mode (7-bit address)
I
2
C Slave mode (10-bit address)
I
2
C Slave mode (7-bit address), with start and
stop bit interrupts enabled for firmware master
mode support
I
2
C Slave mode (10-bit address), with start and
stop bit interrupts enabled for firmware master
mode support
I
2
C start and stop bit interrupts enabled for firm-
ware master mode support, slave mode idle
Selection of any I
2
C mode, with the SSPEN bit set,
forces the SCL and SDA pins to be operated as open
drain outputs, provided these pins are programmed to
inputs by setting the appropriate TRISC bits.
Additional information on SSP I
2
C operation may be
found in the PICmicro Mid-Range Reference Manual,
(DS33023).
8.3.1
SLAVE MODE
In slave mode, the SCL and SDA pins must be config-
ured as inputs (TRISC<4:3> set). The SSP module will
override the input state with the output data when
required (slave-transmitter).
When an address is matched or the data transfer after
an address match is received, the hardware automati-
cally will generate the acknowledge (ACK) pulse, and
load the SSPBUF register with the received value in the
SSPSR register.
There are certain conditions that will cause the SSP
module not to give this ACK pulse. This happens if
either of the following conditions occur:
a)
The buffer full bit BF (SSPSTAT<0>) was set
before the transfer was completed.
b)
The overflow bit SSPOV (SSPCON<6>) was set
before the transfer was completed.
In this case, the SSPSR register value is not loaded
into the SSPBUF, but bit SSPIF (PIR1<3>) is set.
Table 8-2 shows what happens when a data transfer
byte is received, given the status of bits BF and SSPOV.
The shaded cells show the condition where user soft-
ware did not properly clear the overflow condition. Flag
bit BF is cleared by reading the SSPBUF register, while
bit SSPOV is cleared through software.
The SCL clock input must have a minimum high and
low for proper operation. The high and low times of the
I
2
C specification, as well as the requirement of the SSP
module, is shown in timing parameter #100, T
HIGH
, and
parameter #101, T
LOW
.
Read
Write
SSPSR reg
Match detect
SSPADD reg
Start and
Stop bit detect
SSPBUF reg
Internal
Data Bus
Addr Match
Set, Reset
S, P bits
(SSPSTAT reg)
RC3/SCK/SCL
RC4/
SDI/
SDA
shift
clock
MSb
LSb
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C63A | 8-Bit CMOS Microcontrollers with A/D Converter(8位、帶A/D轉換器的CMOS微控制器) |
| PIC16C73B | 8-Bit CMOS Microcontrollers with A/D Converter(帶A/D轉換器的8位CMOS微控制器) |
| PIC16C63 | 8-Bit CMOS Microcontrollers |
| PIC16C64 | 8-Bit CMOS Microcontrollers |
| PIC16C65 | 8-Bit CMOS Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC16C62B/JW | 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16C62B-04/SO | 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16C62B-04/SP | 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16C62B-04/SP | 制造商:Microchip Technology Inc 功能描述:IC 8BIT CMOS MCU 16C62 SDIL28 |
| PIC16C62B-04/SS | 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 22 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。